WATCH THIS now! | Pusher PowerFlow Intake piping KIT - 6.7 Ford Superduty

[@PowerStrokeTechTalkwARod]

To remove the 2020+ intakes watch this video --------> kzbin.info/www/bejne/Z3Scd5WEmrdqbKs To remove the 11-19 intakes watch this video -----> kzbin.info/www/bejne/pnPWlYmXn9RphKs

[@jim-kalliedunn-md4bz]

What city and state do you work out of?

[@PowerStrokeTechTalkwARod]

Detroit

[@22Tremor67]

This pusher setup is definitely nice! Curious as to why more folks are not upgrading the intercoolers on these trucks. Seems like the next logical upgrade especially if you're already replacing all the piping. Another great video ARod!

[@lanehammer]

I agree . The factory intercooler is restricted- mishimoto has proven dyno results.

[@howardbarber3767]

Well.... they are around $3k. Sooo... there's that.

[@jasoncox2132]

I don’t know why everyone says these trucks are so hard to work on. ARod makes it look fairly easy! 👍🏼

[@betterthanideserve76]

I did their full kit in red with coolant reroute and their coupler for the ccv reroute while keeping the ccv in place, new style with no filter acts like a catch can. Their air filter housing clips right to the lower filter housing. Pretty slick kit but damn expensive. I love it, so much room to do activities now. Real easy to get to the cp4 when my S&S DCR arrives.

[@phillipherrington7191]

I can’t find the full kit with the intake filter for my 2020? Where did you find it?

[@betterthanideserve76]

@@phillipherrington7191 on their website

[@BarnStangz]

Looks like a very quality product and your attention to detail during the install is second to none, as per usual. Very nice.

[@PowerStrokeTechTalkwARod]

Budddddy

[@nickp6065]

I like the way the EGR cooler gets reinstalled back on the motor it gives you so much more room... 😉 nice job A-Rod

[@Brandonpowerstroke]

Hey Arod, I see this guy removed his factory fog lights. I can see the block off. Let him know that he needs to remove the far right connector from the ECM (if standing in front of the truck facing the ECM) if he gets water in the connectors underneath the truck, it will backfeed into the ECM and cause all kinds of problems. Just unplug the connector and leave it off. They sell a plug for that port.

[@PowerStrokeTechTalkwARod]

Will pass it along

[@CNKCLAN2]

This has to be the sickest kit I've ever seen. Has to be the one for me!

[@caddidon]

I put my emission compliant intake tubes with a Mishimoto intercooler and boost tubes on my 22 and what a huge difference. Pusher makes great stuff

[@mikemike827]

What did you see diff. Mpg’s …power? Torque.

[@cwcweldingfabricationandrepair]

I just want Ford to start painting the blocks on these engines..... preferably blue💪🏼💪🏼💪🏼

[@PowerStrokeTechTalkwARod]

Riiiifht

[@coryjohnson3946]

Ohhhhhhhh snap! I put mine on not to long ago. The truck freaking BREATHS now!

[@kbdesignz5808]

Is it still running all stock other than the pipes?

[@coryjohnson3946]

@@kbdesignz5808 emissions on tuning from Duramax tuner. Spe cat fuel filter system. Spe hot and cold side pipes. Spe thermostats a banks ram air intake. Next on the wish list is the S&S fuel pump that just dropped.

[@kbdesignz5808]

What year is your truck? Miles? Mine is stock emissions on. I’m at 183k it’s a 2012.

[@coryjohnson3946]

@@kbdesignz5808 2021 right at 36k

[@kbdesignz5808]

@@coryjohnson3946 nice! CC shortbed?

[@JeffreyWilstone]

I think I’m going to get this intake system for mine! Then upgrading the cp4 to the dcr will be easier for whomever I get to do that job!

[@PowerStrokeTechTalkwARod]

Come see us!!!

[@TonyBenton0728]

The Blue Man Group and Papa Smurf would be happy 😃 I would prefer red or stainless.

[@adamholsapple7486]

They are suppose to be having those for the 2011-2016s by the end of the year! I reached out to them few weeks ago about it to do on my 2012! Clean looks!

[@tonycloutier8148]

I talk to Pusher when SPE came out a kit for the 2012 dual intake tubes and they said they weren’t going to make a kit for those years so hopefully they changed their minds because I will buy it if it comes out

[@adamholsapple7486]

@@tonycloutier8148 same! I emailed about it and they said they were working it so we shall see!!

[@rayc5255]

2016 here interested how thar goes and especially performance gains

[@crwoodjr]

I'm glad I'm not the only one who has issues with parts flying out of their hands while trying to push them together 😂

[@jamjon85]

That looks really good imma check if they have it for the 2016.

[@d.williams6891]

Thank you so much for showcasing this!! I’m planning to order this blue piping kit and a jet blue Stage 1 KC turbo to pair with my Sinister Diesel intercooler pipes. 😍

[@PowerStrokeTechTalkwARod]

Id be getting these pipes 1st

[@d.williams6891]

@@PowerStrokeTechTalkwARod Roger that good sir! My truck is a 2015 so I have to order the 2017 pedestal kit for the KC turbo. Do you think it will cause any fitment issues with this piping kit?

[@PowerStrokeTechTalkwARod]

Nawww

[@dougmiller8221]

That was a lot of work hope they enjoy it wish we closer together I could keep you busy thanks for all you show us

[@dv7431]

I bought mine 3 months ago love it great quality

[@PowerStrokeTechTalkwARod]

Yes! Their products are great, all made in USA too

[@darrelwilson2875]

Thats beautiful!

[@timsmothers8740]

You definitely Earned Your $$on that installation. And I'm a Blue man too I, have a Sinister Diesel intake horn and CAC pipes on my 05 6.0l and also a BD Diesel intercooler and a Mishimoto radiator. Fine work by you my friend. Thanks again for the top-notch content that you provide us.

[@spartanoverlanding300]

Just got my titanium colored set a pipes for my 18 and also went the SPE reroute kit and new turbo coolant hose. Just need to find time to install. Might need to take a sick day to make it happen….

[@NycCitizen]

Bought it last month and installed this weekend. Everything went well and no codes. BUT, if I idle for a long time or do an OCR, my pusher pipes laser temp at 190 degrees by the butterfly valve and over 200 after the egr connection. Driving around town the temp is 50 to 75 degrees less. Plan on putting heat proof tape on the electrical and various hoses in a the area Of the pusher intake. Performance wise, Sounds great and my boost spins up faster

[@PowerStrokeTechTalkwARod]

Buddy your stock intake is gonna be the same temperature

[@zekester1]

@NycCitizen Hey, it looks like your into keeping track of temps & maybe other data...you need to get a Banks idash(Super Gauge and/or the Data Monster) to stay on top of truck's info/health👍💪💯

[@PowerStrokeTechTalkwARod]

Amen brotha

[@loft306]

I just stumbled over pushers hot and cold side tubes lastnight because I can get them in blue and then looking around. I stumbled over this(but for 15-19) and I was wondering your thoughts on it, So I’ll just keep watching. Love it, I think I’m going to do this, collecting other parts at the moment and do a whole lot of top of the engine stuff at the same time.

[@PowerStrokeTechTalkwARod]

The client loves it

[@loft306]

@@PowerStrokeTechTalkwARod The thing other than the looks that I like the most out of it is that the air is not smacking up against the wall and then the swirling to the left them up and over and that they’re feeding the EGR in line with it, and it is too cool that they just set it up to where they could just flip the EGR tube over. I mean, this is absolute KISS(keep it simple stupid).

[@WeekendHobbyMechanic]

Nice work!. What are the HP and fuel average gains of this system?

[@alanragsdale9220]

Looks good!! Like the old 352 or 390's fresh rebuild painted that pretty blue color.

[@travismurray4467]

Did the pusher on my 16 F350. Way more throttle response.

[@Fl-diesel-Mechanic]

Just installed on my 19 F350 with the h&s intercooler piping

[@natey891]

Looking noiceeee!! Hot side rubber boots were very snug for me too!

[@patriotone755]

Beautiful work!

[@jeffconley819]

Gotta use alcohol to wipe down the outside of the pipe . That helps a ton

[@bp1012]

It’d be nice if we could get these upgrades for the 2011’s out here without a turbo upgrade.

[@raider762]

A way to secure those coolant lines would be zip tie with a metal eyelet x2, bolt the eyelet under a lower intake bracket bolt and one under a throttle body bolt.

[@tonycloutier8148]

I have the same hot and cold side pipes on my truck ur fingers get a workout with those boots but black pipes

[@DS-TRUCKS]

Omg. Imagine that in black

[@PowerStrokeTechTalkwARod]

Wait its dstrucks

[@FollowingtheCliffNotes]

@@PowerStrokeTechTalkwARod deep sleep trucks

[@rickrichardson5329]

Love that blue. Does this help or increase the performance of the engine.

[@PowerStrokeTechTalkwARod]

Yes

[@nysucks4508]

Nice job as usual 👏

[@jerryknorr679]

Very very nicely done ARod, you should sign ur name on the pipe by ARod. Thanks for sharing buddy ur the best

[@alanragsdale9220]

When You were tightning the bottom of blue intake tube. It sounded like the Starship Enterprise was reving up to take off in the background.

[@PowerStrokeTechTalkwARod]

😭😭😭😭😭😭😭😭😭😭

[@dougcjohn]

Great detailed video, always enjoy the time you take to catch all the angles & details. This project is absolutely beautiful new Blue parts! Although, Other than replacing the aluminum casting manifolds, and adding pretty blue. What is the purpose of this replacement modification? Is there an improvement in breathing, cooling or performance if turbo & boost remain the same and all emission components remain? I see the benefit adding air ram / air cleaner replacement with a Banks… adds improvement on the air intake but this kit for the Price, I’m not seeing the gain or improvement. The additional kit, adding the intercooler new piping, if boost remain the same, additional strength isn’t needed from new piping, what is the gain in that kit? Totally nice looking, but very pricey for under the hood pretties & color accents… all parts over $1,700.

[@PowerStrokeTechTalkwARod]

Did u happen to look at their parts description

[@dougcjohn]

@@PowerStrokeTechTalkwARod Yes, and heard / read about the improved flow CFM. Which is important on the naturally aspirated side, not as important on the turbo’s pressure side. I understand it improves & smooths the path of induction to heads, but under pressure that’s not a major improvement… air density hasn’t improved at the cylinder ports…. Turbo Boost & Air Density remain essentially the same. Agree, it’s beautiful and cleans up the top side of motor. That has worth too, but question the gains.

[@zekester1]

​​@@dougcjohnHey, hope your having a great day!...Here's the advantages in improving air flow on the pressure side of turbo: one, less resistance allows the turbo to spool up quicker and fill the cylinder space faster & easier. Two, since the turbo is operating more efficiently and then you can utilize the extra air available from a better flowing intake. Three, a turbo that runs more efficiently tends to have less wear and thus a longer life. Also, many that is running the Pusher PowerFlow intake & Turbo Inlet has report improved mpg from .5 to 2. In my case (2018 F350 XLT cc lb drw) I've seen from 16.7mpg to 17.4 mpg

[@dougcjohn]

⁠​⁠@@zekester1 Appreciate the info. I realized turbo would gain some efficiency due to improved smoothness & bends, thus aiding spooling time but didn’t think it would provide much performance improvement on a stock emission engine with stock turbo & exhaust emissions restricted. I can see a mild improvement, just questioned the value to have that minimal gain for the price. Several other options provide more substantial gains at a much better cost/gain ratio. Exp: Derringer or Ram Air Intake. The MPG results are interesting, the fuel combustion, computer matrix for A/F & Turbo control unchanged and exhaust remains emission restrictive. I can see a MPG minimal improvement with no load daily driving since power is not being demanded, even the minimal improvement not being utilized, but under load there could be more improvement. Although I can see improvement if combined with Banks pedal and derringer added since derringer is tweaking fuel, air & boost based on readings and pedal monster helping to stabilize pedal input. If dressing up the engine bay while adding a mild improvement is End Goal… then cost to dress up can be justified if that’s the goal. Personally, I’ll probably add these pipes when I get to stage to replace CP4 pump with DCR or Desaster kit mainly for 1) improved serviceability & access, and 2) clean design & beautiful blue pipes. 3) Help performance gains with Banks components. Along the same thought path… I like the Banks 5” Exhaust. Back pressure reducing & performance/MPG minimal gain expectation isn’t the end game… goal is to lower exhaust temp blown back across pricey 5th Wheel and a nice mild turbo tone change…. Gladly take any MPG/Performance gains but not high expectations.

[@zekester1]

@@dougcjohn Hey, I agree with most of your thoughts. Let me explain my 6.7 powerstroke journey...I drove my new '18 dually about 1 1/2 years before putting on mods (except for Banks iDash after 6 months)...Then pulled the trigger on more Banks stuff( had Banks stuff on my 6.0) another iDash(Data Monster), the Ram Air cai, 5" monster exhaust, Derringer set @ power level 3 & Pedal Monster set @ city level 10...Those mods delivered not only more power but my mpg went from 16.2 to 16.7...Drove it that way until July this year( only adding HSM cold side charge tubes)...In July had ARod change out CP4 to DCR, Pusher PowerFlow intake & Turbo Inlet, HSM hot side charge tubes, PPE lower oil pan....These mods as stated before mpg's went from 16.7 to 17.4 also the Pusher intake gave me a quicker response so I lower my pedal Monster setting from City level 10 to city level 8... Now I have too keep my urges in check because the Pusher has a Bad Ass growling sound!!!😉🤣👍💪💯

[@magnuseriksson5721]

I have too say it looks very nice

[@zekester1]

OH HELL YEAH!!!!!🤩😍👍💪💯

[@himni1]

Love the blue. How closely does it match the velocity blue? I’ve been wanting this since they released it. I’ll get it eventually.

[@ninorcsinned3465]

How do you purge the fuel system after disconecting all those lines?

[@Jamest315]

Sick install ARod! Can you link your wobble set you always use with your power ratchet?

[@PowerStrokeTechTalkwARod]

amzn.to/3J2BUkW There ya go🫡

[@Jamest315]

😎

[@Rickystakpants]

I want to see dyno numbers before and after.

[@LeeH-Ranger83]

Thoughts / recommendations: I have a 2019 F350 6.7L Powerstroke. - Pusher versus No Limits Fab kits?

[@PowerStrokeTechTalkwARod]

Bro, Pusher alllll day!

[@LeeH-Ranger83]

@@PowerStrokeTechTalkwARod - which Pusher kit did you use for Marc from KYD?

[@WeekendHobbyMechanic]

I email the company and they said the system nets roughly 66% better flow better than OEM. They didn't test for HP gains. (Too bad)

[@Davee94]

Looks so good! does it do anything for power?

[@PowerStrokeTechTalkwARod]

Better throttle response

[@ozzymed8136]

The hot and cold side pipes are supposed to have some flex. The silicone boots will not last. I have learned from experience. I put a piping kit on my powerstroke and after three months they were trash. Torque will tear them silicone boots. Better boot kit with more flex is around $250.00 dollars. Nothing like breaking down in the middle of nowhere and no parts available.

[@timbo_slice4053]

I've had silicone boots on my truck for over 5 years. Your boots were probably trash quality to begin with.

[@almorrow8158]

Saving my pennies for this kit

[@PowerStrokeTechTalkwARod]

You will like, big difference

[@HammerdownMotorsportsUSA]

looks awesome

[@PowerStrokeTechTalkwARod]

Hey i juss seen you

[@HammerdownMotorsportsUSA]

@@PowerStrokeTechTalkwARod yeah buddy

[@timf6916]

Nice looking

[@charlesklippel92]

Hello mister A-Rod what do you think about the SPE hotside pipe for the 2022 super duty 6.7 diesel Love your videos sir

[@PowerStrokeTechTalkwARod]

Hey thanks bub, i have nothing to say.....

[@spartanoverlanding300]

Any suggestions on turbo coolant line while it’s all apart? I have 50k for mileage just looking for preventative maintenance stuff with all the new accessibility.

[@PowerStrokeTechTalkwARod]

I cobbled one together so there wasn't that line anymore

[@BLADES1320]

@PowerStroke Tech Talk w/ARod Question for you. I recently purchased a VCM3 and all licenses. I have a small fleet of Super Duty trucks. Can you flash the TCM without flashing the PCM? Some of the trucks have custom tunes. I'd like to retain the custom PCM tunes, but flash the TCM. Thank you!

[@PowerStrokeTechTalkwARod]

No, unfortunately, the flash sequence does all the modules

[@BLADES1320]

@PowerStroke Tech Talk w/ARod Thank you!

[@bobowens9359]

tell me about the stuff covering and protecting the grille work. would work well working on old car projects

[@bobowens9359]

What brand and name ?

[@PowerStrokeTechTalkwARod]

I gotta look at the box

[@Brandonpowerstroke]

Noice

[@matthewgraham7419]

What type of silicon do you use to lube boots? I typically use a soapy water solution as any time I have used silicon I have fought the boost tubes blowing off… just curious what type you are using that doesn’t hinder the tubes ability to seal? Great work sir!!

[@PowerStrokeTechTalkwARod]

I think i showed u in the video, 3m

[@jasongriffin1127]

I’m looking at these for sure. Do they really make ANY difference?

[@PowerStrokeTechTalkwARod]

Yee

[@davestewart9146]

Sweeeeet, I like it 👍😁

[@tomslaughter7436]

Gosh darn it just take my $$$$ !!!

[@PowerStrokeTechTalkwARod]

Taking!!

[@tekman196]

Have you had any issues installing these aftermarket pipes to the throttle bodies ? After the third O-ring tearing and leaking I removed my aftermarket S&S pipe and just put the factory pipe back on . I will say that S&S did send me replacement O-rings at no charge . I just lost confidence in the design . The part was extremely hard to install and almost impossible to not tear the O-ring . This kit you put on seems to be allot better designed. Awesome installation video .

[@PowerStrokeTechTalkwARod]

S&S doesnt make pipes

[@lanehammer]

You’ve convinced me to do this with my 2016.. The only thing that scares me is the EGR part .. If I get it out in one piece, would you recommend drilling and tapping for a larger EGR exhaust manifold bolts?

[@PowerStrokeTechTalkwARod]

No. I'd watch the video I have of repairing the EGR broken bolts

[@lanehammer]

@@PowerStrokeTechTalkwARod Thanks

[@akbychoice]

That top silicone boot needs a lip to contain the clamp.

[@toddoconnell8470]

Pretty 😍

[@PowerStrokeTechTalkwARod]

Bud...

[@AverageOverlander]

Are there any HP/TQ gains or just better throttle response?

[@PowerStrokeTechTalkwARod]

Measureable maybe....tell a difference YES!

[@AverageOverlander]

@@PowerStrokeTechTalkwARodthanks for the reply. It's odd that for the amount of money that they charge that they don't list or mention if there is any performance gain.

[@LocoSOB]

Man, it's a shame the rusty little pipe from the EGR cooler has to go connected to such pretty blue pipes 😂 Can that be painted at all?

[@PowerStrokeTechTalkwARod]

I mean, sure, yeah. It can be painting

[@ishmelly210]

Do a 2016 or older models MPD piping kits!!

[@Uncle_Fester24]

Does it work with the HSM hot and cold pipes? Or one big kit?

[@PowerStrokeTechTalkwARod]

It will yes!!!

[@jesusbecerra8590]

Is this kit better than spe kit??

[@liam10345]

Any thoughts on the s&b pipes? i purchased a cold side pipe and cold air intake and haven’t had any issues. Waiting for them to come out with the hot side pipe for the 2022 super duty.

[@PowerStrokeTechTalkwARod]

Ehhh

[@AppalachianPatriot]

21:27 Gravity!

[@vincenttucker2017]

Do you have to do a turn on the truck after installing it? or is it good to go as is?

[@PowerStrokeTechTalkwARod]

Good to go!

[@richardrobinson3895]

Arod this maybe a dumb question but if it's getting more air isn't going to need more fuel to compenate just asking?

[@PowerStrokeTechTalkwARod]

That way of thinking is strictly for gasoline. We do not have 2 calculate that on a diesel

[@burnair1608]

Newbie here what is the benefit to this induction system? Can you get to the pump to install the disaster kit without removing the induction system?

[@zekester1]

Hey Mike, the system flows 15% more air to the turbo & 66% more to the intake which is right up there to their off-road intake systems...better throttle response & mileage gains of .5 - 2 mpg depending truck set up & driving habits

[@josebarba7305]

Banks Power Ram-Air Intake would it void my new 2022 ford f450 vehicle warranty

[@PowerStrokeTechTalkwARod]

No. Dont forget that white sticker under your hood above head lamp

[@dallon507]

30:22 I really want to order this setup but this 1 clamp may stop me from feeling comfortable about it..

[@PowerStrokeTechTalkwARod]

This was the 1st kit. Since we have done about 100 of these. They are great. Tip USE VASOLINE! Wish I wlda used that as lube last time. Sooo much better to work with.

[@dallon507]

@@PowerStrokeTechTalkwARod you’re the man. Thank you 🙏🏻

[@kevinshuford8498]

Man I wish you would have started the truck to let us hear it.

[@FollowingtheCliffNotes]

What’s up there fella

[@PowerStrokeTechTalkwARod]

Wiffy biffy hiffy

[@FollowingtheCliffNotes]

@@PowerStrokeTechTalkwARod is it the weekend yet?

[@CPsGarage]

​@@FollowingtheCliffNotes for you it's Friday 😂

[@gnxtc2]

Use hairspray instead of silicone spray. The hairspray is slippery and has a nice bite to it so the couplers won't blow off. He needs the SPE coolant re-route kit.

[@croutster8399]

Anything BUT SPE …junk customer service and mediocre quality vs other aftermarket companies

[@christiandavis3910]

Pusher has a reroute kit, kinda surprised someone would spend $1500 and not spend the extra hundred for the reroute kit to clean up the engine bay.

[@PowerStrokeTechTalkwARod]

I know riggt, guy did listen i guess

[@gnxtc2]

​@@croutster8399 Although I heard the same about SPE, I have the coolant hose re-route kit and have no issues.

[@chrisgilliam8294]

@@christiandavis3910 Doesn't appear that Pusher has the reroute kit for the 2020+ trucks

[@Brandonpowerstroke]

I don’t like that they powder coated the flange mating surface and the inside

[@nativeoutdoors1780]

Yeah I'd be worried about paint eventually flaking off into the intake

[@DS-TRUCKS]

​@@nativeoutdoors1780 powder coat will be fine

[@nativeoutdoors1780]

@@DS-TRUCKS I hope so haha I doubt this brand would make a part like this and not have forethought to ensure it won't cause problems. So I agree with you thag it'll be fine haha

[@geraldrackley803]

What does this do to your factory warranty?

[@tonycloutier8148]

AROD could u talk to pusher about making a lower dual tube for the 2011 and up models

[@PowerStrokeTechTalkwARod]

Sure will

[@tonycloutier8148]

AROD I asked them to make that pipe but they told me that everyone goes the 2015 turbo so instead of making that pipe they want u to spend 3000 for a updated turbo plus install just to upgrade those sweet pipes I already have the pusher hot and cold pipes Not everyone wants to replace a turbo that still works good

[@christiandavis3910]

They’re not going to because most folks do the retrofit upgrade and use the newer turbo.

[@chadgagnon4070]

Is this upgrade Carb approved for emissions clean air rules?

[@PowerStrokeTechTalkwARod]

Yes, it maintains all factory connections. Visit Pushers site

[@justingreen5918]

Do you need a tune to run this set up or can you run it stock?

[@zekester1]

Hey Justin, the Pusher Powerflow Intake & Turbo Inlet was designed for use with OEM equipment & stock tuning..(as per Pusher)the Turbo Inlet flows 15% more than stock & the Powerflow Intake flows 66% more than stock....you can use stock hot & cold side charge tubes + the stock air intake can be used or your preferred aftermarket ones.

[@jers9375]

Great info I was going to do this while my truck is still under the 100k but also on the verge of trimming some fat in the engine bay but I'm still on the fence but think if I can do this for now at least it will be one thing already install waiting to unleash the full potential

[@aaronphillips2728]

What's this diffrence vs mpd kit?

[@PowerStrokeTechTalkwARod]

🤷‍♂️

[@ewangelbeck]

Might be a redundant question. But does this affect the factory warranty?

[@PowerStrokeTechTalkwARod]

No

[@vincer8691]

Does this void your warrant?

[@PowerStrokeTechTalkwARod]

No

[@NycCitizen]

Got the system. P0069 code. Map drops to 6 or 7 at shut down. If it takes more than 20 seconds for the map to reach aap, p0069 is set by pcm. Pusher baffled. Doesn’t happen with stock system. Apparently the exhuast turbo blades pulls a vaccine thru the egr tube which pusher terminates near the map. Had to remove the map oring to prevent the p0069. Getting a little exhuast smell but no p0969. Sensors are new. Thinking about drilling a hole in throttle body valve to help equalize pressure faster. Ideas anyone?

[@JmF250]

I can't wait until they have a CARB number for this🤣😭😡

[@PowerStrokeTechTalkwARod]

Soon, soon

[@vincer8691]

Dyno numbers?

[@PowerStrokeTechTalkwARod]

We dont have a dyno

[@zachgensler8397]

SPE makes a kit to clean up all those coolants lines. its fairly cheap and well worth it.

[@PowerStrokeTechTalkwARod]

Nahhhh

[@zachgensler8397]

@@PowerStrokeTechTalkwARod you dont think its worth it? or dislike the lines getting rearranged?

[@PowerStrokeTechTalkwARod]

...i have ZERO comment on them...bout it

[@jasoncox2132]

ARod is saying he won’t talk about SPE stuff. But I agree that a coolant reroute is a must with this setup! 👍🏼

[@zachgensler8397]

@@jasoncox2132 im clearly missing something regarding that relationship. lol thanks for the info?

[@edwardmyers1746]

Hmmmm. Not too sure how I feel about the inside being painted.

[@PowerStrokeTechTalkwARod]

Ok

[@marekkon-vw7ld]

Hey guys anybody know how to remove 5G chip from 23 F250

[@PowerStrokeTechTalkwARod]

🫠 i bid you good luck, cuz it a i n t g o n n a h a p p e n

[@zachstevenson4000]

If I was doing this video it would have been instantly demonetized

[@PowerStrokeTechTalkwARod]

Im sry

[@SelectSportsApparel]

Good install, appreciate the video, but what’s with using the word “Millies” every time you refer to a mm socket? Sounds like a 14yo trying to make words sound cool. Blue powder looks great, just cringed every time those metal clamps slid across that fresh finish.

[@PowerStrokeTechTalkwARod]

Aye yo gimmie that 8 milly

[@67_PowerStroke]

Way overpriced. $1200 for some piping....

[@forspamhaha]

Any idea what Intercooler would be worth switching to for my 22 f250 6.7

[@PowerStrokeTechTalkwARod]

Thats a good question

[@louie3552]

NoLimits intercooler as a replacement. Installed it with aftermarket pipes.