X32 Fader Replacement

After something was dropped on my X32 two of the faders were playing up. This video shows how to replace the faders.
Do not attempt unless you are competent with electronics or if your X32 is still under warranty.
Parts available here: www.yourspares....

[@andrew2004sydney]

I had two faders that were mucking up. I unscrewed it like you have shown and just blew compressed air into it. This dislodged a few hairs that were in it and it works fine now without replacing the faders (Have done about 400-500 shows so far!)

[@dcgfhgjnzgfnjcbgn5828]

2 most important parts of the whole video were blocked by an arm, then out of focus.

[@LuisGarcia-se1dt]

Could you help me to get a behringer x32 Main PCB board please ? I’m having issues with the one I’m using.

[@arbenzg6037]

Good evening, about two days ago I changed all the motorized Faders on my Behringer but I don't know what happened, because now I play the same scenes and everything is heard very quietly... even with the Faders at 100%. We have even had to put 4 db more in a digital processor to see what happens, but I'm sorry everything sounds underpowered to me.

[@acidstorm001]

How about cleaning them with electric cleaner and then using fader lube on them? Mine are getting dirty from doing shows in the desert. I use an air compressor to clean mine, but a couple faders are beginning to stick or sit in wrong position and the volume control is not smooth anymore on the one fader. The console isn't even a year old yet.

[@jasango]

hello, for the side buttons (bus button) that are not really sensible to the pressure? which component i need to buy? thank you!

[@phiankguitar8929]

where do you get spare parts like that? I also want to order a new input module spare part for my x32 mixer.

[@bonnymutua]

The dca and main board having a problem with calibration the 0 level is at -20 how do you fix this

[@clementrondwasser1193]

Hello, after desolving, the faulty fader doesn't remove. Why?

[@krzysiekskoczek]

X32 need calibration fader or something like that, after replacement?

[@acidstorm001]

No. It will work after installing.

[@Gladingson1]

I just loved your video, but there is one thing I noticed, when you were prefixing the new faders or fader, those places were out of focus, any reason

[@PeteGaryga]

Thanks for the comment. Unfortunately my camera starts hunting to focus sometimes, it's very annoying and not intentional.

[@mauricelechenault3814]

@@PeteGaryga The disadvantage of wanting to make a video alone, without controlling what is filmed. A friend can do that, the video would be better. See your forearms rather than see what you unsoldered it's silly.

[@rciancia]

You should have cleaned the flux on that board after soldering.. the flux is like acid and will eat away at the PCB

[@RestorationLifeChurchKY]

How long do these faders last when new? My church is looking at getting this board but I am wondering about longevity.

[@IngeGenaroGonzalez]

Plus Berhinger offers a full 3 year warranty. That is hard to beat

[@patovega]

In my church i have a couple of faders that are not working and another two showing signs of wearing. board is about 4 years old and we got it in a period when church went thru a lot of renovations, so lots of dust/cement and other debris in the environment, didn't expect faders to last this long

[@huguesmouflard4826]

Loup noir d.haity

[@colehaaf4425]

I have seen an x32 in a store for demo with a bad fader. It really could go at any time.

[@prismlightning]

My church has had ours for about 5 years, no bad faders yet but a couple of mute buttons went bad and a few of the potentiometers below the screen are getting kinda finicky.

[@ledochapelao]

boa tarde minha mesa x32 e de 16 canais e nao esta aparecendo o icone de cabo usb pois quero gravar um show via cabo usb e nao aparece sabes me dizer algo sobre isso?

[@jorginhoaudio40]

TOWES Dias Olá amigo! Procure por páginas de grupos da Bheringer x32 no Facebook ou site do Tiago Borges para mais informações! Forte abraço e boa sorte...

[@yutube4u]

Good job sir very hardworking

[@eduardoparajon9544]

very good , lo vamos a guardar para tenerlo de referencia

[@patovega]

what are the earth tags?

[@brendan2621]

Pins that ground the electrical signal.

[@Pertamax7-HD]

ok sir

[@TimmyP1955]

Clean the flux from the board with denatured alcohol and a Q-Tip.

[@BigHeartedMan65]

Could you redo it all and in Focus this time . Great Effort . Thanks

[@Gasper84]

great tutorial. Thank you

[@atcordice]

Behringer need to make the board modular

[@kg4gav]

That adds a LOT of cost.

[@16LiveRecords]

My man... Nice edit, but by desoldering, you almost ruined that board. Also you should wash that black remains, because with humodity and little bot of dust, you gan get serious issues... :(

[@MalvinCollado]

Hey muy buen trabajo

[@pritamstudioparoli4011]

Supar naic repeyar

[@28rwags]

Isn't that gay they are plastic faders? When I got mine I ordered a set of real metal faders. So no one be fooled they are plastic.

[@kenchamful]

"Isn't that gay"? Please define "Gay" as you are using it in the sentence above.

[@colabyegtd1687]

@@kenchamful the poster who calls himself "Richard Wagner" also can't tell us where he got "real metal faders." just a troll

[@alanching2317]

VERY BAD VIDEO SHOOTING

[@PeteGaryga]

So sorry. Feel free to re-make it yourself.