Dell Inspiron 15 5567 Disassembly / FAN Cleaning

[@ethanpickwick9142]

Thank you, my friend! I have just replaced a broken fan on my Dell Inspiron 5567. I would never have had the confidence without your excellent video. Thank you for saving me the £60 my local repair guy asked.

[@stevenaughton9372]

At 5:33 the ribbon cable (or whatever you call it) is pulled out and at 5:48 when you come back, the cable has been plugged back in. This is a little tricky to plug back in because the parts are so tiny. On my model there was one screw that I could unscrew from the motherboard, and I figured out that there is a little cover that clamps down over the tip of the ribbon cable that you have to flip down, position the cable in place, then flip it back up. Also it's hard to see, you can only see it from the side. But after a couple tries I got it to clamp in. Anyway, thanks, I could not have done it without your video.

[@LaptopDisassembly]

Well I did this video long time ago. I did fount about this cable the hard way. I just lift the board a little bit and just plug the cable with a tweezers.

[@user-qm7bp4ul5t]

you are the best, thanks for sharing this, i was so pissed at OP for fogetting about this, but you saved my day thx,.

[@leehigham4205]

Thank you so much for this tutorial. You’ve just saved me a ton of money and now my laptop is up and running again. Many thanks 😊

[@filmvideos5779]

Thanks, that saved my day. The air outlet at the fan was covered with a thick layer of dust, fan always on high and noisy. After cleaning it is now quiet and the temp lower.

[@robj2704]

1. This computer, and maybe others as well, requires different screw bit sizes. I happened to have bought a computer tool kit some time ago and found that it contained the necessary bits to do this. The kit also had plastic pry bars so I would not be using a metal pry bar which can potentially contact circuitry on the components. I bought the kit on Amazon for about $30(US). 2. Also, it is very important as soon as you remove the cover to disconnect the battery so there will not be any power available to the circuits. 3. Also, be sure, when doing this job, that the air where you live is not too dry and static which can cause a spark (static electricity) between your hand and the computer components. These components use very minute voltages and the circuits can be easily damaged. Most of us don't live in East India which is a humid climate. The kit I bought did have a grounding strap I used between my wrist and the metal frame of the computer while I was working on it.

[@LaptopDisassembly]

I do lapotps for about 15 years, and so far no problem with the static electricity. But good advises.

[@staceyfurse4041]

Thank you for this video - was able to clean my fan and now it's working again :)

[@k0u2099]

Destroyed some screws but could change the battery successfully, thanks

[@TB-vj6pf]

Thank you so much, you saved my computer and me! Arigato Gozaimashita!

[@LaptopDisassembly]

That's what thees videos are all about.

[@omarb.9979]

I have the same laptop and often times the fan just gets really loud. It sounds like a grinding noise. Is it possible to take off the fan piece without having to take off the heat sink?

[@LaptopDisassembly]

Not possible... The screws are on the top, so in order to remove the plastic you need space inder it.

[@fuatcancagatay4518]

I have this laptop too. His sounds like a fucking jet engine xd

[@ma_r1o24]

I have the same laptop too and the sound is so annoying. Has anyone figured out how to fix this?

[@JHinsonMusic]

Did you watch the video? What do you think he is doing?@@ma_r1o24

[@kamenivanov3902]

How do you attach the small cable again at 5:45 which is under the fan the white one with the green scripts on it I tried to rewind and see when you put it back in place but can't see you doing it and I can't seem to find myself how to do it any help :) ? Great video tho thumbs up !

[@LaptopDisassembly]

I did pause the video, while cleaning the fan. The longer and safest way is to remove the board screws and the hinge and lift the board. This way it is very easy to plug it back. I did use a tweezers and plug it the way the board is. It is more risky so i advice you to lift the board a little bit... not the hole one.

[@cagrbozkurt400]

@@LaptopDisassembly can u create a new video how can we plug it back this white cable ?

[@LaptopDisassembly]

@@cagrbozkurt400 the laptop is not mine, and i already give it to the customer. The safest way is just to remove the board and to flip it up side down. It is held by few screws ...

[@cagrbozkurt400]

@@LaptopDisassembly m gonna be crazy. İ cant remove because screw is stuck. Please help me, how can i plug it back without remove all card ?

[@LaptopDisassembly]

No other way... Or you can use a tweezers and carefully plug it back.

[@LuisMartinez-qf2wr]

how to plug the cable for the power button?

[@LaptopDisassembly]

There is an easy way and a hard way. The easy way is to remove the screws on the board and to flip it up side down. Thw hard way is to remove the screws on the left side and just to lift the board a little bit. Than using tweezers to plug back the cable.

[@LuisMartinez-qf2wr]

@@LaptopDisassembly Finally did it the hard way, but was not that hard. Thanks a lot for your videos and support, great work!.

[@DON-P48LO]

Same question bro I'm afraid of that

[@LaptopDisassembly]

The design is very stupid. The cable is with double side tape and it is stick to the fan.

[@jvanava152]

What's the ribbon that's taped underneath the fan for?

[@LaptopDisassembly]

for the power button.

[@jvanava152]

Tnx, I managed to put it back up and the power button does seems to be just fine.

[@robj2704]

I found that I had to unscrew and raise up the board where this cable connects in order to properly reinstall it. It's pretty much impossible to do so otherwise. If I had seen that it was glued to the underside of the fan housing when I was lifting it off, I could possibly have held the cable down with a plastic pry tool while lifting the fan off and I wouldn't have had to take the board loose to reattach it. Don't know if I would have been able to pry it successfully this way, but would like to have been able to at least try anyway.

[@m.r.a.sandroidzone3464]

hello sir. Great tutorial. i have the same laptop, but it came with the version of 2GB VRAM. Can i upgrade the GraphicCard with the version of 4GB.. it will work or it will not be recognized ? Both versions of the laptop has the dedicated GraphicCard of AMD Radeon R7 M445 GDDR5 VRAM Thank you.

[@LaptopDisassembly]

You can't replace the video, it is soldered on the board.

[@DischaFairy]

Im not really sure how to put back the power cable. It is something to plug or just touch contact surface?

[@LaptopDisassembly]

It is with a lock mechanism. Like the keyboard connector. Lift the black plastic, plug the cable and lock back.

[@sancarkoksal9379]

Çok teşekkür ederim kardeşim.

[@IvanIvanov-os2sf]

Hello thank you for this guide but i pulled the fan accidentally and i ripped the wire for the power button off now it wont start what do i do? Is it possible to connect it back or i must give it to service?

[@LaptopDisassembly]

Just lift the left side of the board, and plug back the cable. The connector is a few cm. Inside... It is not that hard.

[@IvanIvanov-os2sf]

@@LaptopDisassembly it was on the side of the fan its the one under the fan it was glued

[@LaptopDisassembly]

@@IvanIvanov-os2sf it shouldn't be glued but with a connector. BG?

[@ZVEKOfficial]

Fixing the white ribbon underneath the fan is the most annoying thing I have ever experienced in this world. If only you had mentioned to hold on to the ribbon rather than taking it out of the motherboard I wouldn't have to go through all this pain of fixing it back in. The laptop won't even turn on now. Will update after I try and remove the motherboard and pry the ribbon back in its slot

[@ZVEKOfficial]

Update: (2hrs later) I FIXED IT! I had to disassemble the entire laptop. After removing all the Motherboards cables I was finally able to take it out of the laptop casing. I then attached the white ribbon (which actually is used to turn on the power button of the laptop) inside its slot underneath the motherboard. You really need to remove each and every single cable and wire to get the motherboard out btw. Horrible laptop design to be honest. But I'm happy I was able to get the job done.

[@robj2704]

@@ZVEKOfficial Yep. It's a bugger.

[@ujjvalw2684]

@@ZVEKOfficial oh no now it's my turn. I fucked up

[@vehbirestelica2243]

Hi Janko! I just cleaned the fan but now the power button is not working... Do you know the reason??

[@LaptopDisassembly]

Did you lift the board. Thw power cable go under the dvd and under the board. Probably you unplug it by accident. Sometimes the cooler is glued to the place where the cabel goes. Only way is to remove tge screws on the board, lift it a bit a plug back the cable.

[@vehbirestelica2243]

Okay thanks for the fast reply. I noticed the power button cable is unplugged. Gonna try to plug it the way you said

[@ulasanlgunes9132]

Same thing happened to me man. The power cable is the glued underneath the fan right? Its like a band. Where do I plug that, I could not understamd. Could you help me pls?

[@LaptopDisassembly]

It is the power button cable. You have to lift the board and connect it. The connector is on the other side of the board.

[@ulasanlgunes9132]

Yep I just disassembled the whole thing. I am a student so it was a nice experience overall. Thank you guys :)

[@dhirpurohit9119]

Bro please tell which screw driver is used on the cd/dvd side i am not able to open it

[@LaptopDisassembly]

I use BT-8912 set www.amazon.in/Generic-BT-8912-Screwdriver-Notebook-Disassembly/dp/B06VVHBP58

[@DivineOnAir]

Bro in my dell 5567 i hear a loud noise in my fan . I dont know what to do. Should i change my fan or what? Pls reply me bro

[@LaptopDisassembly]

First clean the dust from it, replace the thermal paste and test again. Probably is overheating

[@DivineOnAir]

@@LaptopDisassembly i checked it bro but not working. I mean the sound like fan hitting somewhere when spining

[@LaptopDisassembly]

can be a little bend and it can rub the metal plate.... try to bend it backwards... or replace the fan.

[@DivineOnAir]

@@LaptopDisassembly ok bro.thnks ❤️

[@subwolff]

@@DivineOnAir Did u replace the fan or clean it? I have the same issue right now with the sound like fan hitting something :(

[@ahmedgad2426]

outstanding!

[@dumbstruckweeb]

Is it necessary to use thermal paste?

[@LaptopDisassembly]

Yes

[@robj2704]

Strangely, I saw a video saying this fan noise is a software issue. But, I've put a new fan in mine and it no longer makes a noise. It was $10. on Amazon.

[@Tsiqara]

i cant find part number for fan. Can you please point where on amazon you found one. Thanks in advance.

[@robj2704]

@@Tsiqara I just searched by description of "fan for 5567 Dell".

[@Tsiqara]

@@robj2704 Thank you

[@xerez62610]

Gracias

[@krnkbabu]

Bro. Can you tell me exactly which tool did you use to remove the M 2x2 screw over the Optical Drive. I tried a lot of screwdrivers but couldn't find the right one. Thanks in advance!!!

[@LaptopDisassembly]

As you can see on the video i use the same screwdriver tip like on the reset od the screws. Are you shure your screw is not rounded.

[@krnkbabu]

@@LaptopDisassembly I was referring to the last three screws that you were removing at 1:40. The flat screws.

[@LaptopDisassembly]

In order not to change the tip of my screwdriver i use a smaller one from phone repair kit. They sold them when you buy a battery or something else. These screws are a bit tricky.. You have to push a bit harder before twisting..

[@krnkbabu]

@@LaptopDisassembly That's great of you. Thanks for the info.

[@yumnatimsaal3807]

I have Dell Inspiron 15 i5 8th Gen 8GB for the last 2.5 years but now it makes such a LOUD noise if I open more than 2 tabs on chrome. It even heats up a lot. Should I go for fan cleaning and thermal replacement as well?

[@LaptopDisassembly]

100% but use a good quality thermal paste.

[@yumnatimsaal3807]

@@LaptopDisassembly alright! Thank you so much for your prompt reply.

[@robj2704]

I had to do this same thing on an older Dell I had a few years ago; I'll explain in this text why I did it). I learned a lot from that experience. The reason I went looking for a video on how to remove the computer cover from this newer model (5567) was because the cooling fan in mine suddenly started making a loud noise. For a day or so prior to the fan making noise, I noticed the fan was running on a high speed and the fan exhaust area (on the back of the computer where the screen meets the base) was very warm. I'm going to share a few observations here I experienced when I did mine. The absolute first thing I did when I removed the back cover was to unplug the battery to remove the possibility of powering any of the circuits; it's easy to accidentally hit the power button when flipping the computer over to disassemble it. I removed the fan assembly carefully while holding down on the ribbon cable that passes underneath the fan housing with a plastic (not metal) pry bar. This eliminates having to remove and reinstall the board in order to reconnect this (power) cable (if you're not sure you were able to keep this cable held in place, remove the board by removing it's screws and unplug and replug the cable). I cleaned the fan blades with a fine bristle brush. Possibly the computer was not assembled with the proper amount of paste to keep the processor operating cool enough (I had an older Dell computer a few years ago where the person assembling it had applied way too much paste and it never did run cool). Don't overuse this paste - use an amount similar to what this youtuber did in the video. If you use too much paste, the heat will not leave the CPU area quickly enough (the heat will migrate into the surrounding areas). Also, don't press down on the heat sink when replacing it onto the CPU. You will notice the screws that hold the CPU in place are spring-loaded. These spring loaded screws will automatically apply the correct amount of pressure. Just guide the heat sink into place over the CPU and install the screws while gently keeping the CPU in place. Cleaning the fan blades and replacing the paste on the CPU (my model doesn't also have the GPU because it's not a gaming computer and doesn't have a GPU) seems to have solved the problem. It's now running coolly and quietly. I don't think these cooling fans are intended to run all the time the computer is running, just when the CPU and/or GPU get(s) hot. The temperature in these components tell the cooling fan when to run, and the fan cycles on and off as necessary.

[@yumnatimsaal3807]

sorry to bother you but I should get the fan replaced or cleaned? The guy at the store said that the fan isn't working and needs to be replaced but I am feeling a bit sceptical about it. Would love prompt advice TIA

[@LaptopDisassembly]

How did the guy in the store find out that the fan is not working. It is possible the fan to go bad, but it is very rare. Usually with a little machine oil it runs smoothly. But if he test it and it douse nit spin at all, than you need to replace it.

[@DON-P48LO]

5:20 how to plug that cable back

[@LaptopDisassembly]

You have to remove the board screws and lift the left side. The connector is right next to the fan on the other side. A bit stupid design but...

[@DON-P48LO]

@@LaptopDisassembly can you please do another video clearly please

[@DON-P48LO]

@@LaptopDisassembly can I put it back without removing the motherboard

[@LaptopDisassembly]

I dont have the same lapotp in the office right now. If you have tweezers, you can just lift the board a little bit and plug it back.

[@DON-P48LO]

@@LaptopDisassembly is it easy?

[@ahmadsyauqinafismdyusof]

Hey dunno if you still reply. Just wondering, can the tube part of the heatsink be detached from the fan? bcs the ones that are sold only sell the fan, so idk if i have fo connect it back a certain way

[@LaptopDisassembly]

Yes, you can separate them, but first you have to lift the cooler. After that you have to remove the type on the bottom side, and the fan can be separated.

[@ahmadsyauqinafismdyusof]

@@LaptopDisassembly thanks for still replying!

[@Shehab_Zexas]

does this laptop have thermal pads anywhere ?

[@LaptopDisassembly]

No pads, only paste on the cpu and gpu.

[@Shehab_Zexas]

@@LaptopDisassembly thanks alot

[@faisalsabir3899]

I have the same laptop. It goes to sleep automatically when I press the power button it again gets on. Also charging port is loose. It's very hard to connect charging at some point. What could be the issue?

[@LaptopDisassembly]

Is the battery working fine. I had a lot of cases with similar problems. In most of them it was a bad battery. Try disconnecting it and test without it. About the charger, probably it is damaged and you need to replace it.

[@faisalsabir3899]

@@LaptopDisassembly Battery is not in good health so the sleep issue relates to this. I already bought a charging jack but have no time to visit the shop to get it installed and also do a battery replacement. -_-

[@vimal-dh5yn]

Hello I did the same you shown but my laptop is not getting start only the power switch is not showing light in it. Wile charging its showing the charging light but laptop is not getting on pls help me what to do now.

[@LaptopDisassembly]

Probably, when you lift the cooler, you disconnect the power button cable. Now you have to lift the board and connect it. It is the thin white cable that is going under the fan.

[@nevilholmes5900]

How to install power button circuit om main board

[@LaptopDisassembly]

Lift the left side of the board and reconnect it.

[@nadeemakramansari1331]

Does it have NVME slot bro?

[@LaptopDisassembly]

No

[@MoyMoy_22]

What should I do if I installed a new fan and heatsink but I am still getting a error that the processor fan is not responding correctly?

[@LaptopDisassembly]

Can be a bios issue, or a thermal sensor issue. Try flashing bios, if that douse not help you need to take it to a service shop.

[@MoyMoy_22]

@@LaptopDisassembly How should I flash the bios? Sorry for asking.

[@MoyMoy_22]

@@LaptopDisassembly never mind I know what to do. Its just that I am already on my latest bios for the laptop. Should I downgrade the Bios?

[@LaptopDisassembly]

@@MoyMoy_22 well you can try with older one for test. If is the same you can always get the new again.

[@LaptopDisassembly]

@@MoyMoy_22 download the bios from dell site. It will be exe file. Just start it and follow the procedure.

[@riyanshah663]

My laptop creates a hissing noise and it freezes for couple of seconds and gets back to normal. Also the back part of laptop gets hot. What should i do?

[@LaptopDisassembly]

It is normal for the back cover to get hot. You can clean it and replace the thermal paste. About the freezing... check the hard drive with crystalDisk for bad sectors.

[@Tsiqara]

Some one, where can i buy replacement fan, Please. I cant find any info. Thanks for help in advance

[@LaptopDisassembly]

This should be the one www.amazon.com/ZHENHUIYOUYUE-Inspiron-FCN-FJ0D-DFS481305MC0T/dp/B073YMVR45

[@epath4957]

How much thermal paste should I buy for this? I can't really tell the capacity of that syringe you used in the video... I reaaaally don't want to get at it and find out I don't have enough. I´d love to just buy a 20gr syringe and be done with it for a good while but tbh I can't afford that rn :/

[@LaptopDisassembly]

20gr is way much. I use big syringe coz I use it everyday. You can just put a small drop like been and just use your finger to make it even. It has to be a thin layer at the end.

[@epath4957]

@@LaptopDisassembly I see, thank you!

[@althafsyed3251]

Does Dell Inspiron 5567 fan sucks air or blows air ?

[@LaptopDisassembly]

It suck from the keyboard and blow it from the grill

[@monica-mi5lx]

Hello, I did everything You do in the video and now My computer does not turn on, What do I do??? Help me pleaseee!!!

[@LaptopDisassembly]

Well apparently something went not according to video. Douse the laptop power on, any picture... Try reseating the ram memory... More info will be helpful

[@LaptopDisassembly]

Probably when you lift the cooler you did unplug the power button cable. Check the cable. If that is the case you need to lift the board a little and just plug the cable back.

[@monica-mi5lx]

I exactly have the problem with the power button cable, how to lift the board? can you tell me, please? or can you recommend a video about this problem?

[@LaptopDisassembly]

@@monica-mi5lx You have to remove the srews on the board. After that just lift the left side of the board. It is a regular connector on the end of the board. Just plug the cable back and close the mechanism.

[@harshadpj524]

Hello sir, i have the same laptop should i put thermal pads for chips which is left to the gpu ( the 2 big ones) ??

[@LaptopDisassembly]

If they have by default yes, if no than it is not a good idea because you can lift the hole cooler and may not cool properly.

[@harshadpj524]

@@LaptopDisassembly thanks

[@MilekaRobot]

"Like and subscribe if you like the video." Sorin school ;) Good job!

[@fahimbaig5914]

My dell inspiron 5567 fan not working sometimes and laptop stuck on application like phhotoshop and becomes very hot i am having core i 5 7th gen 8gb ram with 256gb ssd what can i do ? Plz help

[@LaptopDisassembly]

Try to replace the thermal paste first

[@jimd7241]

Hello, I've tried just about everything... I replaced the fan&Heatsink in a Dell 17-5767 Now the Fan is running wide open all the time... error message saying fan not responding correctly...In the bios the the fan isn't showing the RPM's...Any ideals? I've tried about everything...unplugged battery for 30 sec held power button for 30 second's...unplugged the small 2032 battery for 10 mins... Did the thermal paste over..unplugged the fan and plugged back up...reset the laptop...tried a old bios firmware...tried my old fan which still works,BUT IT ALSO runs at highest rpms now... Trying to think of everything I've tried...Did the new fan do some kind of hardware change???? Any way gonna order another fan and try that,I guess Thanks

[@LaptopDisassembly]

Have you try with the latest bios from the dell site. If that douse not help, there may be a problem with the thermal sensor. It is telling the laptop that the it is hot and it needs to be cooled. Also did you try different windows. I had cases with bad OS with same behavior.

[@jimd7241]

@@LaptopDisassembly Thanks Tried just about everything

[@jimd7241]

@@LaptopDisassembly any thing you can google I HAVE TRIED lol

[@jimd7241]

@@LaptopDisassembly Hey Buddy ...The fan plug on the motherboard had a prong/pin for the blue wire broke,And luckily,I was able to solder the blue wire to the broke prong/pin....Doesn't look the best,But got it working...Thanks for trying to help..Take Care

[@LaptopDisassembly]

This is totally different story.. It is for the rpm of the fan. Whrn not connect the tan is working in high rpm.

[@youpeeps6433]

somewhat helpful video. but would be better if you zoomed in more. you didn’t show getting the power button cable back in, and now i have to take the whole motherboard out.

[@LaptopDisassembly]

Yep, note taken... It is 3y old video. I try to show more now. You need to remove the screws on the left side. Just lift the board a little and you can plug it with a tweezers. I haven't got the same model since than, to make ver. 2.0 of the video.

[@NeonLightification]

Hey buddy your discord link invite has expired. I'd like to join it.

[@LaptopDisassembly]

It is not my own discord, but here you go. invite.ers.repair

[@CrankyJoeJr]

This was really helpful, but bad thing is, it didnt workon my laptop, it kind of made it worse and i think the prosessor is over heating

[@LaptopDisassembly]

You did replace the thermal paste and connect the fan, right? Double check is it laying properly on the cpu.

[@CrankyJoeJr]

​@@LaptopDisassembly the layout should be correctly, but the thermal paste, thats something i dont have

[@LaptopDisassembly]

@@CrankyJoeJr well, how did you replace it than. You CAN'T clean the old one and put back the cooler without new paste.

[@CrankyJoeJr]

@@LaptopDisassembly ooooooh, that might be the reason

[@nottodaymate6607]

me - took of termostuff... And then he says "apply new one". I'm like "damn, I don't have any"

[@LaptopDisassembly]

I was like that first time i reinstall my windwos 98. Followed a tutorial, i wrote format c: .. after that they says, now insert windows 98 installation media... and i was like... crap...

[@iagaro]

valeu fera, Brasil

[@travistouchdown9448]

I like how he did not show how to plug the power button back in

[@LaptopDisassembly]

I know, i know... It was one of my first videos. The connector is at the end of the left side. Just remove the board screws, lift it a little and plug it back. It is not that hard.

[@cadoo5591]

What??? I want to see you clean the thermal face. Next video

[@LaptopDisassembly]

What is a thermal face? Also to clean the paste just use some IPA and a paper and just clean it. Nothing hard.

[@adhamsmhody]

لماذا الحاسوب محمول الخاص بي من نوع Dell بطيء للغاية رغم مواصفاته العالية حيث أنه يحتوي على الجيل السابع من معالج إنتل Core i7 وذاكرة وصول عشوائي بسعة 16 جيجابايت وبطاقة رسوميات بسعة 4 جيجابايت؟ هارديسك SSD حتى بعد تثبيت نسخة ويندوز جديدة

[@LaptopDisassembly]

Is the laptop with regular hard drive or with a SSD one. can you write me the hdd model.

[@adhamsmhody]

SAMSUNG MZ7TY256HDHP-000L7: 256.0 GB Firmware MAT04L6Q S307NB0J545738 Serial Number Interface Serial ATA Total Host Reads Total Host Writes 15853 GB Rotation Rate ----(SSD) Transfer Mode SATA/600 | SATA/600 Power On Count 3288 count Drive Letter C: E: Power On Hours 26373 GB 7325 hours re Standard ACS-2 | ATA8-ACS version 4c Features S.M.A.R.T., NCQ, TRIM, DevSleep, GPL

[@LaptopDisassembly]

Check the hard drive with CristalDisk to see is the disk in good health.

[@adhamsmhody]

The hard disk has been verified using Crystal Disk. The disk is in good condition

[@LaptopDisassembly]

Well you can try to check for viruses is r make a fresh install. Also check in task manager to see what is slowing the computer... Check the hard drive and CPU section.

[@LaptopDisassembly]

Discord - invite.itjungle.eu If you have any questions, regarding Laptop repair and etc. you can join and ask for help.

[@user-qm7bp4ul5t]

you didnt plug the power button back in on camera, I was here for that, thanks for nothing.

[@sus8575]

5:24 May i ask you what is the wire below the fan please? I do not know what is that for

[@user-qm7bp4ul5t]

@@sus8575 dont ask me, ask OP

[@CristianValentinNegritas]

how to replace fun to the mb ? the pin has broken

[@LaptopDisassembly]

The pins on the board are broken or?

[@huseyin4134]

I plugged the power cord back in but when I turn on my computer it just gets a black screen, what should I do?

[@huseyin4134]

my computer is working but the usual dell text is not coming

[@LaptopDisassembly]

Check did you plug the power button correct. Also try replug the ram memory and LCD cable.

[@dhruvmehra7203]

@@huseyin4134 did it work ?