Keep them in the freezer and fry or air fry as need.

Excellent video in these tough times, I struggled like f*** to push the caliper in, then I thought, I'm doing something wrong and this can't be that hard, I took your advice and bought the tool to push the caliper in and it was plain sailing from there on 😂, thanks for the guidance 👍

I am in the process of refurbishing my Fobco Star Drilling machine and unfortunately the top aluminium belt cover has been damaged. LOOKING for A REPLACEMENT BELT COVER. Stripping the Quill was fairly straight forward as I removed the top circle and using a plastic pipe I drove the Quill up and out of the main body casting. The labels came off very easily with WD40 and purchasing the paint from PARAGON ENAMEL PAINTS

Could you use this for cans?

Does this do front and back labels?

have you given up making videos ?

Hello, I am a homebrewer and I am trying to start a nano brewery you have no Idea how much your videos help me sir, thank you very much

Just bought one of those MT-50 labelers from Vevor (May 2024). For the money it is not too bad, but I found (what I call) the "label carousel" surgical tubing friction system to be pretty hokey. I replaced the roller shaft with a 1" diameter bar, bushed the side plates down to one inch, then used felt washers on the side against the mounting plate and a spring and shaft collar on the outside for tension. I also did not like how the liner paper rubbed on the motor under neath... so I made and added another roller between the knurled front roller and the take up roller. The factory should have mounted the motor at the back of this machine. Since everything is chain they could have mounted the motor anywhere other than where it is. Fortunately, I have the skills to do all of this. But for the price ($350 USD) you still can't beat it.

fantastic clip, enjoyed it a lot and learned something new, thanks

no explanation about the dremel & how you fixed it.

Have you had to replace any fuses?

Struggling to find it anywhere for 350 quid pal

From the looks of his Instagram it looks like he's still alive but appears to have split from Gemma and his kids and has hooked up with some lass called Alice who's still at uni 😂

Brilliant video that tought me so much thanks

Seriously miss your content! Hope you´re doing fine!

Regarding the addition of a variable speed drive (VFD, or inverter) - a few words of caution from someone who's worked in electronic control of motors for 35+ years. A VFD works by rectifying the incoming three-phase AC to a DC voltage of about 550-600 volts, and then converts that back to AC (at whatever frequency and voltage you wish) using "pulse width modulation" (PWM). Without going into all the details (a Google search will give you lots more if you want it) the resulting voltage waveform that's applied to your old motor is quite different from the 50-60Hz sine wave voltage for which it was designed. The inverter or VFD applies rectangular voltage pulses to the motor windings, with very fast-rising/falling edges (the voltage swings several hundred volts in a small fraction of a microsecond) and this is a lot more stressful to the motor insulation than the ordinary mains supply. Most high quality modern motors are designed for use with inverters, and as such are wound with "inverter grade" enamelled wire which is coated with special insulation designed to withstand the PWM voltage pulses (which can cause voltage stresses in the insulation at well over 1000V.) However, your vintage motor won't be designed for inverter use, and if you connect it directly to a VFD, you may find yourself having to replace it or carry out an expensive rewind after only a short period of use. This can however be avoided by placing a "sine wave filter" between the VFD and the motor. These are available from decent inverter (VFD) manufacturers, and also from companies like RS Components (who supply decent German-made filters from BLOCK). Choose a filter with sufficient current rating for the motor (obviously) and make sure the VFD's switching (PWM carrier) frequency is set to a value suitable for the filter you've selected (e.g. 8kHz). The VFD also needs setting up to provide an output voltage that's essentially proportional to the power frequency ("constant V over f" characteristic). This is easy and any decent drive company will give all the instructions - nothing to fear but does need to be done properly. On the matter of noise, your motor sounds like its bearings are dry and/or have seen better days! Might just be the proximity of the microphone, of course.... ...but if you've got the motor in bits anyway, I'd generally advise replacing the bearings if you can - the motor should run quieter and hopefully you'll reduce the risk of frustrating (and potentially damaging) bearing failures further down the line. Hope helpful, best wishes with it all. I've also inherited one of these drills and am about to start work....

Hey Harry you taken a break from your KZbin videos?

Please give us an update ??

Hi Harry hope everyone is ok. Are you going to post anymore content?

So once you fill the jars with the vinegar ... they can sit on counter for a long time ?

Speaking as an electrician with 30years experience I watched this video between my fingers.

you probably should have a lesser motor for exit air to maintain a fairly high temp inside

are the tomb stones not polarity sensitive? would it work either way round pal

Neat cask washer.

Hi great video I’m new to this I have a hand pull but I have noticed on other peoples videos they say to use a demand valve I between the keg and tap so not sure if I need one and struggled a little to find the right diameter beer line to attach as well

Anyone know if Harry Brew survived the winter❓

Could you use balsamic vinegar in pickled eggs? Just curious

could you please put the three ingredients into the description of the video? ... or confirm what I'm reading from your video frame at 3:50 - "Dimethicone 1000, Methyl Salicylate (something), and the 99% isopropyl alcohol" Ideally: give the mix ratios and recommend immersion time and temperature. Thanks!

.

How much of the Fobco Cream paint was needed? I'm considering a repaint myself.

Thank you for the interesting video, I recently got a similar control unit for the water (got it on Amazon, shipped from china). unfortunately it came without instruction manual... I'm still building the control panel, so next week I will connect it and try it. May I ask if you did any calibration on that unit ? do you happen to have the instruction manual ? (I'm talking only about the unit where you set the volume of water and you pressed run). and by the way, I don't know if you know about this, but when I discovered this thing I was very happy; if you open this unit, you will find inside it that you can connect a thermo couple / thermometer so it will measure the temperature as well. 😀cheers

I put a fresh onion garlic and chicken stock powder in the water when boiling. Also grind up the end seasoning with smoked salt, smoked paprika and a dash of Jamaican all spice in a coffee grinder so it's a very fine misting of powder, then toss the fried scratchings in that. Perfect!

Hey Harry, you okay?

❤❤❤❤❤🎉

Go to minutes10:45

Nice idea.thanks

Have looked at a number of videos on toe and heel, with most being as instructive as remove bead and straighten door!! I mean, like, seriously! This is a brief and excellent video on, not only how to do it, but also the theory behind it which makes it all the more memorable. Also well presented. Well done OP!

Any video that starts with ‘ow do folks’ gets a thumbs up from me! Can’t beat the Northwest

I still don't understand how you wire the HP241G to MT-50, can you guide me?

😀

🤣🤣 You had some minor problems but mate you are brutally honest and thank you for explaining exactly what "Toe & heeling" is 👍 Brilliant video

Hi Harry, I'm a great fan of your vlog. I need current meter with measuring transformers for 3 phases, for my own panel. But I can't seem to find one. Maybe what I'm looking for is similar to the one you use in your panel. Can you help me find one? Greetings from a small brewery in Denmark :))

Came here this see how the put my Dremel back together.. stick to the plan I had to skip right through 🫣😆

Might be an idea to remove cap on brake fluid reservoir this makes it easier to wind piston in . Also check that the slide tubes aren't sticking , these come out to clean and put small amount of copper grease to stop them seizing up . There are torque settings for these bolts and the wheel bolts . Nice video too .

If your bro had been there on the double yellows, the police would have given him a ticket, but not interested in doing their proper job shocking 🫡

Top man, this place is on my list to visit as I love salvaging. I worked at Osberton for 6 years so it’s only down tge road on tge way to Retford 👍

A man of many talents, spent most of tonight watching your vids 👍loving it so as your latest subscriber keep them vids coming Harry 👍

Hi Harry You came up as a recommendation and we thoroughly enjoyed your video. Last Friday we were in Retford and went to the Golden Cod just round the corner from your bar, great fish and chips, we’ll be back and nip in for a swift one and eventually some foo. I married a Harrison so hope you have some gift sets left with a glass and some beer 👍

LOL It's Benny Hill reincarnated! Yep, if you have to have kids, by all means keep them caged up!