2 жыл бұрын
2 жыл бұрын
3 жыл бұрын
3 жыл бұрын
5 жыл бұрын
5 жыл бұрын
Пікірлер
@stephenmoroke1241 4 күн бұрын
Tip,next time you dismantle a pallet,Just shut up😂
@barryredman8232 14 күн бұрын
Playing with blocks really paid off.
@arenuzzle6282 21 күн бұрын
Jesus is good
@nicucristea 21 күн бұрын
Shhhht..i was cutting with saw😂
@thatpinkbee5038 22 күн бұрын
you sir are a genus
@user-tk3jx8mt2h 26 күн бұрын
اليد مقاسها كام لوسمحت
@robertdecuir5748 26 күн бұрын
How simple and efficient can one person get? I will be using your method in the future. Thank you for showing this method to everyone.
@UnknownIdaho 27 күн бұрын
I like making things from pallets but it seems removing the nails is the most time consuming part! Really important to puck GOOD pallets to start with, no use putting this much time into junk…
@alysongrannum9170 29 күн бұрын
EXCELLENT 👏🏾 👏🏾 👏🏾 👍🏾👍🏾👍🏾THANK YOU, Thank You; thank you!! Continued Blessings sir🙇🏿♀️
@Blank201 Ай бұрын
Thanks for showing the way. Going to start dismantling pallets now that I have an endless source of them. I am tight on cash and was looking at all the videos showing methods with pallet busters and air compressor guns to get the nails out. This is absolutely the way I will be going. Ingenuity at its finest.
@SmeeUncleJoe Ай бұрын
Why Rice Bran Oil ??.. That is hard to find and not one we'd use for other stuff.
@lapislignum Ай бұрын
Just because it is fairly cheap and has a high flash point. YMMV
@lapislignum Ай бұрын
Oh, I already bought it for heat treatment, otherwise I wouldn't care much about flash point
@SmeeUncleJoe Ай бұрын
@@lapislignum Do we need a high flash point ? It is an aqueous solution. I would not know where to begin to look for that and I'll bet it's rarity would make it expensive.
@lapislignum Ай бұрын
Just mix any oil with water and some detergent, if it looks milky it will lbw better than nothing. Or buy cutting fluid.
@SmeeUncleJoe Ай бұрын
@@lapislignum I cannot just use regular cutting fluid as they use the same crap as in antifreeze and auto coolant. That splashes on my basement floor . My cats step in it, even when it's dry and then lick it off their paws. They then die a horrible death.
@realexposer Ай бұрын
Which software use used?
@lapislignum Ай бұрын
NanoCAD or draftsight
@beachthor1 Ай бұрын
Genius!
@UncleFjester Ай бұрын
At what I'm worth an hour its cheaper for me to buy fence pickets
@lapislignum Ай бұрын
Look out folks we got us a millionaire here! 😁
@katzgg Ай бұрын
Very nicely done. Will be trying it like this from now on
@FloatingStranglers Ай бұрын
Really good technique. The cleanest pallet dismantling I’ve seen
@Nick_Jarrett Ай бұрын
I did think of using a car jack but thought it would split the wood
@Nick_Jarrett Ай бұрын
I wish all pallets behaved that well, I have a load of pallets with beefy nails or nails that are bent both ends to stop them coming out or ones with ridges to help prevent them coming out
@lapislignum Ай бұрын
Yeah most need more work, I made a video on dismantling a europallet but most of them are more work than the one I used.
@Daily-tm4nx Ай бұрын
IT WORKS i just tried it!! This is some next level Nen Master shit lol thank you so much
@lapislignum Ай бұрын
First comes block, then comes hammer. That was such a good series! Cheers!
@Daily-tm4nx Ай бұрын
@@lapislignum HxH has inspired the best most random assortment of people lol!
@libraman9825 Ай бұрын
ty for this video, i needed this
@jimjimson6208 Ай бұрын
I feel like a fucking dumbass watching this lmfao I can't believe I didn't think of this
@Madtony910 2 ай бұрын
Best and easiest way i've seen.
@valkeriejones3818 2 ай бұрын
Holy shit I am STUNNED
@robhtp3817 2 ай бұрын
Simple, Quick, & most of all Effective ~ THANKS!!!
@BlessedDog 2 ай бұрын
Why can you not do this with a fuel barrel? Is it because of possible combustion (which can be avoided by rinsing the barrel)?
@lapislignum 2 ай бұрын
Yeah basically, rinsing (filling the barrel and emptying it) would work, you could chisel it while full of water to be super safe.
@Johonavich49 2 ай бұрын
Very nice!
@mrs.g5659 2 ай бұрын
Gonna try. Hope it works with a euro pallet to
@lapislignum 2 ай бұрын
I did a video specifically for europallets kzbin.info/www/bejne/Z5LUlpuLrpqWp7M they are a mixed bag but this is a good place to start.
@JohnDoe-ki6fm 3 ай бұрын
Yup! Good! I wonder if you could yank nails even faster in the last step once you have driven them back through the boards by just grabbing nails with the vise-grips (or a pair of channel locks)?
@lapislignum 3 ай бұрын
Not sure that would be faster than the claw of a hammer but I do need some channel locks.
@Purinelz 3 ай бұрын
Oh yeah. You MF you just walked away like you dropped the microphone!
@Purinelz 3 ай бұрын
What the f*** where were you 4 years ago, when I f****** needed this? I'm so stunned. Good job, and thank you for sharing and saving a lot of hours moving forward. Thanks.
@lapislignum 2 ай бұрын
I had to check but 4 years ago this video was 3 years old :) glad you found it now, enjoy pallet boards!
@TerraRoaming 3 ай бұрын
absolutely brilliant
@balooga111atyahoo 3 ай бұрын
How much of it became charcoal? I still see some brown centers on some twigs.
@lapislignum 3 ай бұрын
About 75% ? I wouldn't do it like this again
@OidHunter 3 ай бұрын
Wish we could do that here in UK, most pallets are made 10x stronger than that though 😅
@lapislignum 3 ай бұрын
I made a video with a europallet too, most of them are pretty hard to do.
@MaiNguyen-zp3fs 3 ай бұрын
Thanks sir. You help me a lot for dismantling pallets cause I’m 70 years old. Thanks again.
@MrDynomite123 3 ай бұрын
another video, a guy used a grinder around the edge.. and it popped right out...
@georgesmith3022 3 ай бұрын
Hi friend, what is the thickness of the plywood?
@lapislignum 3 ай бұрын
1/2 inch or 12mm depending on your units
@dave4583 3 ай бұрын
Now give him a “difficult” pallet…
@buns52557 3 ай бұрын
Man” your good with your hands good job on sprocket what kind of motor were you using on the sprocket?
@lapislignum 3 ай бұрын
Cheers! It's an actuator off a heater box out of a car, they rotate continuously.
@tracyboehmer8603 3 ай бұрын
I just fell in love! With intellect and resourcefulness!
@ObamaoZedong 3 ай бұрын
I'm just mad I had to sit through a dozen inferior videos about breaking pallets before I found this gem.
@joelnite 4 ай бұрын
You are so smart bro thank you
@RJ11narendragurjar 4 ай бұрын
Kon sa कैमिकल है
@lapislignum 4 ай бұрын
Cooking oil
@kelvinsparks4651 4 ай бұрын
The simplest ideas are the best and rarely though of , we'll done. The nails must also come out straight so they are easy to tap out .
@lordofsmgs 4 ай бұрын
thats the weakest pallet ive seen. i do a pallet in 5 minutes with half the effort my way
@joelalain 4 ай бұрын
that is brillant, thanks!
@lapislignum 4 ай бұрын
Cheers, I never did anything with this, mainly uploaded so I wouldn't lose the idea.
@Fernando-kb1hp 5 ай бұрын
Excelente👏👏👏👏👌👍👍👍👍👍👍
@donnykiofetzis5775 5 ай бұрын
dose it work with salad dressing.
@lapislignum 5 ай бұрын
Sure!
@tiagovazkez9356 5 ай бұрын
What I wannna know is how to make it into a functional cog in an actual bike
@lapislignum 5 ай бұрын
Probably not like this unless you are desperate
@Fernando-kb1hp 5 ай бұрын
👌👍👍👍👍👍👏👏👏👌👍
@user-ne3di6dw1q 5 ай бұрын
Good 🎉🎉🎉