I was a firm believer in powder coating until I started watching more cerakote videos such as yours. Thank you. I'm wondering, however, what is the more durable coat between the H and C versions? (So oven cure vs. non oven cure).

what media do u use to blast

What year is your engine?

kzbin.infoGfXn8WppIQg?si=BP2kBqwjg-maMjpV

That frame is way too heavy

m.kzbin.info/www/bejne/j37GhoyfqNx3Zqs

That frame is way too heavy and full synthetic lubricants are a bit faster kzbin.infoI1ysfoEh7Kk?si=zEt1QbfuaXzYTJKh

Gas dude you've raised the compression, kzbin.info/www/bejne/h6PIY4mJi9aUh7ssi=92RF7lTplhbHzSR_ I would put the motor in a 2003 kx125 frame is about 40lbs lighter. I would also get a short r304 silencer

How far apart did you do the spacing for your bolt holes on the 4 in flat plate

Might be a dumb question. How do you clean the glass beaker? Just thinner?

Awesome man ika so waych this just got cr 125 need rebuild her so my frist time this going help so much i want learn for my self so i oay less 😂

Hey mate awesome video been following you’re 125 series. Currently building my 07 125 at the moment, if you don’t mind please sharing where you get all the torque specs? Thanks mate 👍🏽

im too scared to fuck everything up

Im into the RC hobby, but im starting to see Shifter Karts as my new hobby😅

Did you use rear hub from CR or newer CRF?

Did the timing ever come into consideration in this rebuild would like to know as rebuilding one myself at the minute

Hey amazing video. I love to do engine building myself. Say what’s the name of the song that starts around 3:45?

Ok I have a question I took the motor out put everything back except one line. I can’t figure out where it goes or I don’t see it. Hopefully you can help. I’m gonna try and send you a photo.

Great job thank you for taking the time to do this huge help. I appreciate it. Have a great day. My safety switch is bad thank you again.

Good job ! Great details. Thank you !

Going to rebuild my first ever dirtbike engine, a 01 yz250, seen the videos, seem easy to do but I fear of messing up hundreds of dollars of parts

You know what’s crazy. 2+ million of us sat here and enjoy someone else putting something together with their hands for 30 minutes with no words. Life’s a trip. 😂

Great job I’m gonna have to watch it a couple of times but thank you for doing it

What happened to your videos I hope you doing good

I’ve bought a 79’ Yamaha yz125 in pretty good condition but I want to take apart the top end before I start trying to run and ride it, does anyone have any tips?

So my seadoo is making connection and making a peep all the lights turn on but i wont fire up .i trying on a quad power sport battery can that be the problem

5 years later and theing joke didnt age well lol i wanna fix my bike but ther is 5 stores near by that repair small engines kinda expensive kinda not

Ive never seen Genuine Mikuni carb kits come in a package like that.

Did the red coat not need electricity? I don't see you connected it back on 8:33

hello Adam love from Cameroon

Very clean build brother !

Did you put grease to the middle gasket? Wth? You should use some silicon gasket staff, not grease!

I have this exact same Seadoo with the same problem. All the lines have been changed. When I put gas down the spark plugs it runs and then shuts off. I looked at the fuel selector. Seems ok. I looked at the fuel filter as well. Im thinking same problem. Last year it ran a bit out of water and shot out alot of white sludge. This year it wont start. I wonder i pushed some of that sludge into the carb.. I'm almost at the point of selling it. They dont make it easy to access everything with my big hands lol😂

Adam your my hero

Thank you!

Where did you get your head stays for the phat head? I just recently bought a bike but they had some home made mounts on it.

I have a dash light but no beep beep… what could be the cause ?

Those don't look like Mikuni parts don't rebuild with aftermarket will cause problems other than that good job

what if you're not getting power to coil?

Hello Adam this Rob , I been watching your videos because I have a 1991 seadoo gt with no spark I have tested all the electricals but nothing my question is does a 1991 seadoo needs a programed key ? Or it can be by pass? In order to get it started? Because I don't have a key. Thanks.

What twist throttle/assy? Should I get? 😂😢

What twist throttle/assy should I get for mine?

Excellent. Very thorough.

that would make a great ornament if you had two of them, one in a frame and one on a coffee table. . .

Great video, I have no power on white wire going to coil. What does that mean

"Similar" concept to Variable Valve Timing in modern car's. Less/more air/fuel based on RPM and duration of valves opening so your car doesn't idle and sound like a dragstrip car to only then run "fine" at 75 mph.

Can you bypass the safety switch?

Do you have any experience troubleshooting a 97 GTI MPEM?

wow great work!

Hi my name is Rob from Toronto after watching this video and doing what you did I still no getting spark mine is a 1991 do any suggestion?