Thanks, I drive a 2016 beetle and it didn’t come any covers for the holes or lighter inserts. I don’t smoke but just wanted a couple for decoration. Simple explanation for how it works.

I have a question about this. I want to hook my modern TV to an old Marantz amp. The TV indeed has an RCA L/R out and Optical out. I assume that would only provide broadcast signal audio from whatever local VHF signals. However, I also thought TV signals are digital now so does the audio portion matter? Lastly, we also primarily use a Roku for streaming apps so I'm not sure how to extract audio from it and get it into my old amplifier. I would assume most people would be facing these same two exact issues. Local broadcast audio and then audio from a streaming device.

Were the vertical brackets included with the TV or did those come with the mount? Thanks.

Thanks man! Been trying for AGES

Ur voice is so annoying I’ll watch a different one

I dont have the plate behind the pad. Does it come with new pads?

0:04 i like rolling coins ❤

Great video but what is the ohm range for these actuators? And which one is A & B? Mins says A is not working...

Nice tip on spinning the slide pins, makes sense.

Thank u big time

This video rocks / if you can’t figure it out, throw your computer away

Great job! I have to do one tomorrow. Thanks, great tutorial 😇🤗

Do you drive the car around to let the gas flow after replacing it? Just replaced mine with the help of your video!

Amazon is a supporter of the scam organization black lives matter, I'll never give them a dime of my money

Wow, that was awesome! I think I'm gonna have to start checking all the coin machines around town and I can probably retire 😂

Is it possible that we replace new thermostat opening on 76 degree.

Any torque specs?

Amazon have fees now...5%

Took me ages to work out to disable s mode before doing windows updates on my new laptop.

Thanks!

I didn’t even see the pads I came to see. All I hear is calliper all day

I noticed you didn't sand it with sandpapers. Does the steel wool kind of do the same job and sands it good enough?

Thank you! Saved me a call and some money to diagnose a simple problem. Glad you covered resetting the thermocouple. That was it.

So far most interesting things I've found in the Coin Star reject bin are a few Mexican coins (some post 1992, some pre 1992) and some tokens that look like they're from a video arcade.

This was one of the best videos that showed us how to use these machines. It's my first time using this machine, I am going tomorrow. I was scared at first!! LOL

The best coin I've found so far is a 1902 Indian head,and a 1917 wheat back penny.

I’m still so confused 😭😭

Epic find!

Perfect!

How to take it down😂

What is the secret to getting the pulley holes and water pump holes to line up when trying to get bolts to secure pulley? I ordered water pump and gasket from Kia. Gasket was metal sandwiched with paper. There are two alignment pins (2 of the water pump bolts go through) that held the gasket while I put the water pump on.

great instructions; simple and to the point; thank you!

Very useful video

Wait...it said the coins went to the Amazon ecard....where's the cash? Sorry I'm confused

Ok, I feel pretty fuckin stupid right now. In my defense, there were no instructions in my box but without this video I would've never taken that rubber piece out or figured out how to lock the handle.

I can't speak for the other years but the 2005 Hyundai Elantra's have drum brakes in the rear.

Thanks so much my friend! I did not know to keep the pilot light depressed for 90 seconds until the unit started flashing. That was the key for me...Saved me a visit from the plumber and $$$

I've used Coin Star a few times in the past. I just roll my coins now.

oh wow i remember when it was 8.9 percent in 2011

I have same this one

All steps where of a great help, in that I've done brakes many times, but like to check a KZbin video prior to replacement. I didn't see how your pushed the caliber piston in, but I use a large C-clamp personally. Second, and something I've always done, is after tightening all wheel lugs, I choose to use my ft/lbs torque wrench, to make sure all lugs are at 80-85 lbs. I will often recheck again after driving the vehicle for a week, just to make sure all have stayed at the recommended torque value.

Thanks for showing this!

Great job!!!

Those rims looks great afterwards, also the rims looks like the ones off from Chevy Cobalt, based on its visual appearance.

Is the CRV the same design as a HRV? I have a 2016 HRV and need to replace the starter.

Great video! Easy instructions for a lady who has never had to light a pilot light, let alone troubleshoot. Thank you so much for saving me time and money. I would have never known about the reset button otherwise.

do you NEED the wind back tool or can i use a C Clamp? im gonna be doing mine in a few days and am making sure i have everything together

Thank you! Thank you! Thank you! You just saved me from being ripped off. 😊 I tried to light the pilot 3 times last night, pausing 10 minutes in between as instructed on my unit. Nothing. The next step is to call for service repair; they don’t mention the reset button at all. Before calling today, I decided to do a quick KZbin search and picked the shortest video with a unit that looked like mine. 😂 JACKPOT!!! 🎰 💰 I wasn’t sure it would work because the reset click was very faint and I don’t have the same view of the pilot flames as you but I did hear the flame ignite and the status light started blinking right away, once every 3 seconds indicating normal status. Thanks again! Feels great being able to do things on my own unlike my helpless mother and myself 10 years ago. Lol

I just rolled a whole bunch of my change and converted it to gold. 😊

I have a 2015 forte and this actually helped find where that freaking cheap part is. Thank you for this as I now can replace that part and get rid of the dang code.