That looks good but only cut out the bad part leave as much factory metal as you can because it's thicker and better than the aftermarket stuff.
@jameslloyd7670 Жыл бұрын
I have a 79 f100 short bead need a lot of cab and bed work
@markwoten66792 жыл бұрын
I got to do that in my 79 F150 Styleside PU.
@kingfordism5 жыл бұрын
Now that I've done this a few times I would add that when fitting your cab corner on for the first time measure the distance between the bottom of the "dent of your dent side" to the raised horizontal part (body line) on the bottom of the door. That way your cab corner lines up with the door, keeping the body lines correct, even when your door doesn't line up to begin with like Devan's was and mine was. Also, close the door every once in a while to check that gap. My cab corner job was a lot worse than this, I had to rebuild most of the underneath parts Devan showed here along with the lower door post.
@Joryja1276 жыл бұрын
Great work man. Fitment was spot on 👌🏼
@DevanEnce6 жыл бұрын
Thank you!!
@michaelsylvester72726 жыл бұрын
Nice work!!
@DevanEnce6 жыл бұрын
Michael Sylvester I appreciate it
@josephsummers79236 жыл бұрын
Ik my one like doesn’t matter to to much but I’ve followed you on insta for a while now but never saw the KZbin side and damn you do good work👍🏻 keep the videos coming they will for sure be enjoyed and definitely are driving me to keep moving on my dent side 😬 again thankyou and keep it up ✌🏼
@DevanEnce6 жыл бұрын
joseph summers your like does matter! Thank you for taking the time to watch the videos. Keep me posted on the progress with your dentside.
@MarcusSchneidervlogs5 жыл бұрын
Looks awesome mate, love the look of it
@markwoten66793 жыл бұрын
It would be nice to tell what tools etc you utilised in your task. I got to do the same on my 79 F150. Cab corners and rockers.
@northwestoff-roadopportuni71762 жыл бұрын
Great job! You north or south ID? I’m north CDA area
@DevanEnce2 жыл бұрын
South Idaho
@jimbascombe77075 жыл бұрын
I have to do the same thing to my 68. They are not real bad as only the bottom is rotten.
@scottscheuerman87146 ай бұрын
Do you put any metal on the inside of where you are going to patch to hold the panel to
@DevanEnce6 ай бұрын
I replace any of the rusty metal on the inside before I put the patch on
@scottscheuerman87146 ай бұрын
@@DevanEnce I figured you would remove the rusted panels completely I was just wondering if you use a strip of metal on the inside on the inside to hold the panel to or was the magnets the only thing holding the panel to the edge
@casimirobuenabista5 жыл бұрын
How different are the f250 from the f150 cab? I have a highboy and i have to do this repair also the roof needs to be replace and the floor pan. 😆 sometimes i think it would be better if i change the whole cab but here in cali is hard to find good parts.
@RedBarnMachineWorks3 ай бұрын
Which brand patch panels do you prefer
@DevanEnce2 ай бұрын
Auto Metal Direct is who I use almost exclusively now
@JGCUSTOMLEDLIGHTS6 жыл бұрын
Hi! Can you post a link to where you got those big cab corners? I have to do the same thing to mine.
@DevanEnce6 жыл бұрын
I have bought them from a number of different places but the shipping is cheap with National Parts Depot. Here is the link www.npdlink.com/1948-1979-ford-truck/body-exterior/body-parts-accessories/cab-parts-1973-1979-cab/cab-walls-roof
@dwaincroghan63116 жыл бұрын
I like what your doing with this project Here’s a tip that might help you if you’re doing lines cutting them or using body fillers is kind of draw line with pencil and use 1”or 2” painters tape
@dwaincroghan63116 жыл бұрын
And double up the tape if you’re sanding that body line so you take off the top piece of tape and still have the bottom one
@dwaincroghan63116 жыл бұрын
1” tape especially for curves
@DevanEnce6 жыл бұрын
That is all fantastic info! I will definitely put it to use
@fordnut49145 жыл бұрын
That seat has more miles than the truck lol... nice job tho.
@endall67833 жыл бұрын
I was liking the vids that is until I noticed you only half fixed the inside. I was wondering why go into it that deep and only do a half ass job. Sorry but that's my opinion I know it don't count but don't do something if it not going to be the right way. Duck tape cheap !