Removing Rust & Paint, Farm Trailer SandBlasting

In this video I sandblast the faces of this farm trailer it was planned to do as much as possible in 1 day then the customer changed his mind and wanted extras to make a better job. So he opted to have an extra 4 hours to get more areas done. 12 hour total job.
Media used was crushed glass grade fine + & medium @100 psi
#sandblasting #dustless #dustlessblasting #mobileblasting #mobileblasting.co.uk #Falch #doff #paintremoval #abrasivecleaning #housecleaning #presurescleaning

[@telekommotorrad9065]

Quick question. If the hay around the truck is being fed to animals, won’t it be full of the blasting media, paint dust and rust?

[@Mobileblaster]

Ah sorry I should have put this in the description this Farm has no livestock they use the hay for the burners I'm no farmer and dint know exactly what they do but big mounds of spuds and soil was everywhere 😂👍💞

[@telekommotorrad9065]

@@Mobileblaster ah that’s good to know! The idea of a cow eating tiny bits of glass made me nervous... cheers!

[@Mobileblaster]

@@telekommotorrad9065 yeah I should have made that clear my fault sorry :)

[@mickdelahunty5026]

Hey mick I'm a blaster also I'm based in wexford in Ireland you done a great job there mate and very little dust well done from one blaster to another 👍

[@Mobileblaster]

@@mickdelahunty5026 thx mate it's appreciated 👍💞

[@roydawson4882]

Nice job as usual mick, once painted they will be fighting over who drags it,stay safe.

[@Mobileblaster]

😂 his main call to action was if it looks good on the road the police are more likely to leave him alone haha with it been Farm 🚜 agricultural registration he don't need to mot it but is restricted to how fast he can go. No mot but he can still get done if its defective like bold tyers no lights etc 👌💞

[@donyboy73]

Nice setup. I like all the sand in your van!

[@Mobileblaster]

😊👍👌

[@aloggins69]

I just love watching sandblasting. It is very soothing to me.

[@Getithowyoulive863]

You should try it sometime.

[@liamnugent4146]

As a blaster myself it's the underneath that's the tough part great video fella

[@Mobileblaster]

I don't mind doing eva but I've learnt not to do stuff I've not been told too 😂

[@twostix67]

I used to do this when i was in my 20s. Filthy noisy sweaty job but i loved it.

[@Mobileblaster]

😂 not half one of the worst jobs if ya like staying clean 😂

[@twostix67]

@@Mobileblaster Nobody hassles you once the grit gets flying though .

[@Mobileblaster]

@@twostix67 haha that's about best bit of job lol sometimes I wish pot would last longer than a hour then other times I wish for it other way round 😄

[@twostix67]

@@Mobileblaster Its strange how those clip board carrying hi viz wearing health and safety wombles stay well out of the way as well lol

[@AllanDeal]

Good job mick

[@Mobileblaster]

Thx mate 👍💞

[@allenzackery1639]

Got it looking like a pencil eraser ! Lol. Nice job 👍

[@Mobileblaster]

magic wand haha :)

[@charleswelch249]

Nice job on a very rusty trailer frame.

[@Mobileblaster]

😊👌👍

[@caycoo]

So satisfying to watch. Words can't describe...

[@Mobileblaster]

😊 I have plenty more feel free to have a snoop through my other videos 👌👍

[@james1c763]

Nice job as usual mick,

[@Mobileblaster]

😊👌👍

[@briancamac4573]

Hahahah dont mind doing them big trailer's as long as there well stripped like that one ur doing now.nice job working with the long blast nozzel. Must get one for myself 🤗😁👍

[@Mobileblaster]

Don't let the sales pitch sway you buying 1 they say they add power it doesn't ad anymore power just that it keeps the hotspot in a tite cone for longer 👌💞

[@briancamac4573]

@@Mobileblaster I know what you mean mate.but they look good to use in awkward places 🤗👍

[@Mobileblaster]

Yeah but are they worth the money? I would say yes as I like the easy life but I could have managed without it. They are expensive but once you have 1 try and only use it when needed that way it will last as long as possible 😊

[@briancamac4573]

@@Mobileblaster yes know what you mean mate.will have to price one on line to see what it costs 😁👍

[@Mobileblaster]

@@briancamac4573 normal nozel £180 ish xl turbo £550 ish depending on who you use 👌 oh and it will were quicker than a normal one 😳

[@Luko247]

Treat yourself to a large O ring to go over hose to slide down onto the deadman trigger won’t have to hold with both hands all the time , however don’t let go of it 👍🏼👍🏼

[@Mobileblaster]

That would be very dangerous 😳🙈 I can set it so I move a slider and it blasts slide it back it stops but even that is too dangerous. As it is if I slip or pass out drop it the blaster etc it will shut down hence the name dead man's handle 😁 I know what your saying but from a safety point it needs to be done like this 💞

[@phillipsharpe6459]

Nice one, from scabby to quite good, 😁👍

[@Mobileblaster]

Quite good 🤪 😂👌💞

[@phillipsharpe6459]

@@Mobileblaster ok brilliant, 😁😗

[@Mobileblaster]

@@phillipsharpe6459 😊😂 for the time involved I would say it's the best thing to happen to that trailer its old he knows that and the value isn't in the trailer to fully refurbishe it all he wanted was it to look good for a few more years 😁👌💞

[@canadianpopeye8066]

Great job your the man Mick.Too bad they don't have nozzles with wider spray pattern be done faster .

[@Mobileblaster]

🤘👌💞

[@Mobileblaster]

They do them but in my experience they seam to work out the same speed or slower as it reduces the psi of the hotspot its kinda hard to explain 🙈😂

[@AylerProductions]

They do have bigger nozzles, but faster means less money, that’s why he white metal blasted it while pointing the nozzle inches away from whatever he was hitting, that should’ve only took a few hours while using way less sand.

[@funone8716]

@@AylerProductions Bingo

[@clevonmendoza8027]

I truly miss doing that job, when I was in Trinidad🇹🇹

[@Mobileblaster]

😬😊👍

[@frankbullitt4556]

Perfect surface to paint.

[@Mobileblaster]

👌👍😊

[@Eggemeyers]

How much media in total weight do you think was blasted in that 12 hours?

[@Mobileblaster]

I cannot remember off top of my head as it was some time ago if was to go do another I would take 1000kgs on the hopes I would be bringing around 350/250kgs home

[@JT-qf4it]

Nice work

[@Mobileblaster]

Thank you 😊

[@Mr.Frost181]

So do they bring it some place else to get it painted

[@Mobileblaster]

No this was painted in place 👌👍

[@scootherring9314]

Go back to first tip an set partial choke on should do great an blow your mind also figure your distance out by moving back an forth

[@Mobileblaster]

using choke would push more sand I don't need more sand? the xl nozzle gives that bit more reach than a normal size nozzle same bore same psi same media just a longer reach with the xl nozzle (all it dose is it keeps the hot spot cone for a longer distance)

[@heribertoortinezgracian2851]

Perdón a que presión trabaja este equipo, gracias por su respuesta.

[@Mobileblaster]

125psi @ 260cfm 👍

[@Canadianduke23]

What do most blasters do blast by the hour or job? How do You know how to charge a customer?

[@Mobileblaster]

I price per job as I know how many hours a job will take me to complete.💞

[@johncarroll4448]

@@Mobileblaster what did you charge for that job

[@Mobileblaster]

@@johncarroll4448 for inquiries please email [e-mail] Regards Mick

[@brantleyrigo4528]

Nicely done! How long did it take you and cfm compressor do you have?

[@Mobileblaster]

12 hour over a day and half 👌 I would have done slightly more if he said he wanted a day and half to start with 😳 but he only decided to do more when he realised it would look better than he thort 💞👌 I use 260cfm @125psi possibly 100psi at the nozzle 👍

[@ashboy225]

Looking good, you cannot beat a sandblasted finish, no rust and so perfectly prepped for painting! - Are you finding that there is a sandblasting material shortage?

[@Mobileblaster]

No only work is drying up since the covid but I'm managing to keep afloat 💖 to be fair I stock 27+ton so I have a little buffer if I've to wait for stock 👌🤘

[@Akaalautopaint]

well nice job brother. Where i can buy this sandblaster in canada?

[@Mobileblaster]

Totally unsure this is my own build I'm waiting to get protected so I can offer it for sale but this process is taking years :(

[@Akaalautopaint]

@@Mobileblaster oh okies..never mind

[@y.lelivelt2619]

Good job!i have a suggestion. Why don't you use a fan or blower to " lead" the dust in the direction YOU want? It gives us, and perhaps you a better sight on what you are doing. Greets from the Netherlands🇳🇱

[@Mobileblaster]

The air mover needed would need to be huge to move the volume of air needed. I'm maxed out as it is with what I'm aloud to carry in the van 😔💞 welcome to the party 👌💞

[@cannonfodder6654]

Whats the most unusual thing you have sandblasted

[@Mobileblaster]

I was in a celler in a funeral parlour to expose some steel structures. When I had to stop to let a funeral take place above me 😵

[@shameless1047]

How much does this one cost? Or rough estimate

[@Mobileblaster]

For all business enquiries please email [e-mail] Regards Mick

[@hry0649]

hello, what sandblaster do you use? greetings from Romania

[@Mobileblaster]

Pressure pot 👍

[@johnriff85]

"can you just" "sure for T&M"😂

[@Mobileblaster]

😂

[@Marshy234]

Great vid, any tips on where to look for info on how you get into this? Pay? Licenses? Etc. Cheers

[@Mobileblaster]

Thx it's appreciated 👌💞 what's you location plz if your outside the UK I have no idea 😂

[@Marshy234]

@@Mobileblaster Manchester 😂 ( U.K.)

[@Mobileblaster]

Ideally you need to do some sort of training from a blast suppliers their is no set rule that you need to but for your safety and other around you I did 😊 then you need to get insurance in place boom your in business 😉 I will just add I do make it look alot easier than it is just like any other trades person that's decent at their job plastering springs to mind it looks easy but I've tried that and it's not haha. I wish you the best of luck tho and if I can help in anyway I will 👌💞

[@Marshy234]

@@Mobileblaster yeah I’m not the type to jump into something lol, defo don’t want to be all gear no idea 😂. I will do some more research on it, thanks for your reply I appreciate it. 👍

[@Mobileblaster]

@@Marshy234 If I could speak to a younger me I would say listen and learn at school so you don't end up getting covered in shite for a living 😂🙈💞 its definitely not for everyone you may be better trying to find a job doing it 1st and seen if you can cope with the helmet 8 hours aday and the dust all over you every day 👌

[@thiagodasilvagomes8834]

Hello friend, do you work with dry and wet blasting?

[@Mobileblaster]

Yes I have the ability to dry/ wet mix at nozel or fully saturated in the pot. Wet on this would be near impossible unless I wanted to get a mortgage to cover the cost of the visors I would need 👌

[@wcsd9577]

Nice work! I like that first song, what's the name of it?

[@Mobileblaster]

Thx it's appreciated 👌👍💞 and sorry I don't know I've downloaded it from the youtube studio and I have a small selection I like off that 👌

[@devininwetrust9610]

I do blasting every day as my profession and trailers are one of the hardest jobs to do..

[@Mobileblaster]

Ooo I don't mind trailers I don't like using anything over 400cfm my next video I have to profile steel 600cfm with steel shot I really don't like using steel shot that stuff hurts well it does at 600cfm blow back haha

[@devininwetrust9610]

@@Mobileblaster totally agree steel shot or slag or pretty much anything that is a really corse media sucks to use. Mostly I use 50/60 green diamond for just about everything.

[@Mobileblaster]

@@devininwetrust9610 I like glass 😊 from super fine to medium that's my go too 👌

[@aaronbyers8200]

What media did you use for this job ?

[@Mobileblaster]

Crushed glass 👍

[@SMWalkerAtelierDeCouture]

I want to buy one of these sandblasting machines?what is the name of it please

[@Mobileblaster]

Pressure pot any will do the bells a whistles are you to you and your workload 👍

[@chadkennedy529]

What size compressor are you running? And what media and psi?

[@Mobileblaster]

Hi its a doosan 260cfm my go too media is crushed glass from dust to medium I think this was fine + and 125psi so around 100psi at the nozzle 🤙

[@keithsarty3039]

Mick! In your honest opinion, would you say blasting is rough on the hands and wrists? Back? Knees? Dirty? Dusty and horrible breathing environments? Ty 😊

[@Mobileblaster]

It's not a nice job by a long shot dust gets everywhere but it can be rewarding. More effort and time you put in the easier it becomes 👌 it is very physically demanding 👍

[@keithsarty3039]

18 year extremely professional painter, have an opportunity to join the painters union, but the rep says sandblasting is a huge part of the jobs.. I know blasting is kind of dangerous and just kinda sucks holding one of those things all day, but the pay is 38 an hour to start and 40 after 3 months, all benefits, all the bells and whistles.. 🤷‍♂️ so I'm trying to see if it's worth it!

[@Mobileblaster]

I believe if your a painter leave the blasting to someone that does blasting why would a skilled painter try to learn another skill? It's like a roofer learning how to lay bricks kinda makes sense but not really haha

[@TxcNtr]

using the nova 2000 mask is good but lack of sand flow is making this project way longer coastng way more money, this should take 8 hours or less. and the nossel tip is to small need something a lil bit wider for faster clear speed

[@Mobileblaster]

Hi I'm using the nova 3 not the 2000 :) each blaster will have their own way of doing things the reasons I do it like this, For any more media flow wouldn't give me a faster cut the only thing that would have gave me a faster cut is heaver media and more air cfm in both cases the media needed to cut slightly faster would have been almost 3x the cost of glass and ive tried it in the past I don't fink it cuts 3x faster. So in my opinion not worth the extra cost. More air would be nice but in the uk I'm limited to what I can tow and my 260cfm is right on the border of my vans safe towing ability. More air would drink more derv in turn only saving a little extra time but adding more cost to the job. The Nozzle/tip is set for 260cfm @100psi a bigger nozzle wouldn't gain anything only slow the job down bigger bore will lower the psi anything below 100psi isn't optimal. Anything over 100psi is unsafe with my pot and nearly every other on the market is rated to operate at this. The job he wanted was quoted 8 hour but he then asked for extras taking it over.

[@ravindernegi7419]

Is the media recyclable?!

[@Mobileblaster]

Yeah its recycled bottle glass. It could be reusable again but for speed of the job I don't reuse the media. Plus once its been used it brakes down and don't leave a uniform finish if its used more than once.

[@ravindernegi7419]

@@Mobileblaster thanks for the information! What about the broken/ worn-out media? It is hard to recollect as it mixed up with soil and therefore contaminating soil or is is recycled into glass again? Anyway great to see your work and even greater was your prompt reply! Cheers 👍👍👍

[@Mobileblaster]

@@ravindernegi7419Thx it's appreciated 😊💞 the media could be used again but I don't for the speed aspect of things. It wouldn't affect the soil/ground as its none carcinogenic and the paint was water based so biodegradable 😊

[@ravindernegi7419]

@@Mobileblaster thanks indeed 👍👍

[@MrWendell50]

Great job Mick. What paint do you recommend for first coat?

[@Mobileblaster]

Thx it's appreciated 👌💞 but I'm no painter 🙄 I wouldn't recommend anything I don't use or know much about 🙈

[@mycarprobs6688]

Epoxy primer is the industry standard for shot blasted trailers. It is a good thick coating that goes on before adding a colour.

[@Mobileblaster]

@@mycarprobs6688 Yeah I've heard my brother mention something like that before. This guy was going down the DTM paint root (direct to metal). Its a all in one other names ive heard people say is rain coat/ one coat, loads of different names but its all the same thing I don't know if it's any good like I say I take paint off not put it on :)

[@Frankiedoodle1941]

Do You sandblast 4x4 Mick ? its a Land Rover Freelander 2

[@Mobileblaster]

What the shell? Or chassis?

[@TiGAStt68]

How much its cost for the sand blaster machine bro..full package

[@Mobileblaster]

For inquiries please email [e-mail] Regards Mick

[@TheCuriousOrbs]

"Just"..... I always roll my eyes when clients use that word. No, it doesn't make your request reasonable and it doesn't diminish the time required to finish the job. I'll "just" invoice you for the additional time taken. How does that sound?

[@Mobileblaster]

@@TheCuriousOrbs 😎😂👌👍

[@Getithowyoulive863]

You should have turned your sand up a bit. would have sped the process up a lot and given you a much better blast profile.

[@Mobileblaster]

I tend to disagree hears my reasoning, If I did turn it up I would have wasted media yeah it would be a little quicker but wasting 60/70% of the extra media (with rebound hitting the stream) when im the 1 buying the gear I find a happy medium with derv(air consumption) and media(coverage) I find if the nozzle sounds like a whistle its too low and extra media could be added if it sounds like a train chu chu chuc etc its way too high anywhere in this range (with out theses sounds) is ideal for me. I find lower media more air makes a better profile as the air has more chance of pushing lower volume of media at higher speeds than big lumps of media thats going to re hit the rebound. I like to try and be in the optimal range :)

[@angel_dawn_morningstar]

by the end of the video , your M-B Sprinter looked as if you had been at the beach all day 🤣😂😏

[@Mobileblaster]

😂😂😂 funny you mention the van I'm just as we text having a little brake and finishing removing the stickers so the next time you see the van eva sticker free or new design I plan on doing these myself I don't know no if to do a video what you think?

[@angel_dawn_morningstar]

@@Mobileblaster Definitely .. a DYI decal application ..We had our M-B vans professionally vinyl wrapped , but that would make excellent video content 😍

[@Mobileblaster]

@@angel_dawn_morningstar only 1 problem I have no idea what I'm doing 😂😂😂

[@Frankiedoodle1941]

THE CHASSIS JUST THAT THE MOT SHOWED IT NEEDS SEIN TOO

[@Mobileblaster]

Don't need MOT with it been agricultural registered that's why he wants to make it look better to keep the plod off his back 😊

[@kashifad3244]

Sir I am blaster and spray painter.sr job have,

[@Mobileblaster]

Sorry not at the moment

[@doniofficial6246]

Hallo I'm DONI from Indonesia

[@Mobileblaster]

Hello and welcome to the party :)

[@bendude6748]

I could do with one of these to blast my car project 😂

[@Mobileblaster]

Saves alot of man hours sanding 😊💞

[@bendude6748]

@@Mobileblaster do you ever get cars in for blasting or is it more industrial sized stuff

[@Mobileblaster]

Yeah I've done quite a few just that I've not had any crop up since doing the youtube channel 😳 maybe 1 or 2 on my channel but nothing with fairly decent editing 😂

[@bendude6748]

@@Mobileblaster Oh nice, what kinda money would you usually charge to do the underside of a car ?

[@Mobileblaster]

@@bendude6748 totally depends on age of car etc if your in Yorkshire send photos to [e-mail] and I can get you a quote 👌 Regards Mick

[@oumarbhatti3316]

Hello sir I have 5 years experience can give me one chance job

[@Mobileblaster]

Hi sorry I'm not setting on just yet 👍

[@Amac-uz9hm]

Must cost a fortune for the medium wasted

[@Mobileblaster]

Not really as this is 1 x hit possibly 2 x but after the 1st hit it brakes up so I wouldn't get a uniform finish. I could use a different media to last longer but the cost is up on that and then the productivity is down so catch 22 some areas it would pay some not so good. Everyone finds their own style and what works for them I add these costs into my price obversely and it seams to be working for me. :)

[@Amac-uz9hm]

@@Mobileblaster yeh it makes sense bud, it probably ran through my mind in a logical way, but I chose to ignore it 😂, I used to paint that stuff a while back and the set up we had was a small warehouse where it would be blasted before the paint went on, and the shot was on the floor to be later swept up to be used again, so I do see the point👍 very therapeutic

[@Mobileblaster]

@@Amac-uz9hm yeah sometimes on the right job and location it would pay to do it that way :)

[@bbgamegodpnw]

My God how are you doing that without gloves, and I pray your wearing a mask man. I sand blast 5 days a week and going 1 minute with a defective mask is hell

[@Mobileblaster]

Yeah I use nova 3 👌 gloves they are only for when it's cold? 😂 I definitely wouldn't recommend it but I know this is no excuse I have alot of experience with my rig and feel confident enough not to blast areas that don't need it ie my digits😂

[@universalturtle9283]

Your not whipping the nozzle in a circle or back and forward

[@Mobileblaster]

😊🤘🤙their is no set way to blast. I will do a tips and tricks video soon as to why I blast like this and the reasons my change how you may think. Keep an eye out for this video soon 😊

[@thelaggingbrit6697]

are you hiring mate?

[@Mobileblaster]

Not at the moment buddy but if you follow my Facebook page mobileblasting.co.uk I put it on their 1st when I am 💞👌👍

[@stelsewhere11]

The "can you just" people ?! ..Uh, So many times in the past that phrase has drawn an exasperated angry response from me that has sometimes ended in violence. sigh.

[@Mobileblaster]

😂 I can say 90% of jobs I do say it 😂

[@stelsewhere11]

@@Mobileblaster lol .. I'm a long haul trucker. When in Penrith a few years ago, the "Can you just drop that at Carlisle, it's just up the road" without understanding the truck does 4 miles to the gallon and costs £4 odd a gallon. And expected to the job for nothing... "Can you just" lol

[@Mobileblaster]

@@stelsewhere11 😂 can you just... lol

[@verossavr3027]

your car is sandblasted too

[@Mobileblaster]

Only a bit of dust 🤗

[@verossavr3027]

@@Mobileblaster i don't think so)

[@Mobileblaster]

@@verossavr3027 it gets alot worse most other days 😂 I'm just on with editing another video and I show a clip of the van getting washed its unrecognisable until water hits it 👌 should be on today at some point I hope 😀👍💞

[@TheManuele7878]

Certo che farlo vicino alle balle di fieno per gli animali é il massimo😭

[@Mobileblaster]

Non c'è bestiame in questa fattoria, coltivano patate. usano il fieno per alimentare i bruciatori :) No livestock is on this farm they grow potatoes. they use the hay to fuel the burners :)

[@joshking8416]

Take the dead man off the hose bro. Don’t hold the nozzle with your hand if it comes off it’s gonna hurt. Your hand should be half on the join and half on the hose. Blast all underside surfaces first. And did I see you blast the threads the tyres bolt onto. Ugh. I’ve blasted for 15 years in Mining oil and gas so maybe a bit fussy. The positive side I’ve seen worse. Lol.

[@Mobileblaster]

If the Nozzle wasn't supposed to be held why has it got nerling on for grip? The job sheet on this was to do the face's none of the underside 👌 the media used won't damage the threads just clean them out I'm able to blast wires and airline's with out busting or cutting through them I know they will be fine 👍 to make a complete perfect job it would need stripping to an inch of its life have it over a pit etc but the man hours alone would value the trailer as scrap all he was after was a tidy up so the old bill don't pull him over as he moves it from 1 field to the next. With it been agricultural it don't need MOT (UK tests to say its safe for the road) same again it won't be pulled any faster than 25mph and a maximum of 1.6km from his farm or land 👍 he just wanted it to look fresher than it did 😊 please have a snoop through my other videos 😊

[@joshking8416]

Understood bro. I’m just extremely fussy. 👍🏽

[@joshking8416]

I’ve seen nozzles come off not a pretty sight. Holding the hose also makes for better control as you can make it do the work for you. 😀

[@Naserallh]

من ایرانی هستم وکارم سندبلاست هستش کار خیلی سختیه اما مجبوریم

[@Mobileblaster]

😊 hi fellow blaster 👋 it's how we keep the lights on I suppose 😂👍

[@Naserallh]

@@Mobileblaster عزیزم لاتین بلد نیستم😇🤣

[@Mobileblaster]

😂 worlds apart 😊 but we are in the blasthood together 👌👍​@Naserallh

[@rhyslewis2062]

Hi pal, watched all your videos as I'm just been starting off blasting people think it's easy but it's not your doing well fair play wouldn't mind your number to have a chat if possible

[@Mobileblaster]

Thx it does look easy but the is more to hit n hope haha. I can answer any questions you may have on hear that way it will help the channel out with other people may have similar questions I don't want to keep repeating myself 💞👌👍

[@rhyslewis2062]

@@Mobileblaster I've been happing trouble with my compressor , compressor oil going in the air lines? I'm after another compressor if you know for any for sale

[@Mobileblaster]

@@rhyslewis2062 What compressor is it? You can easily fix that issue no problem swap out the air oil separator buy a service kit for said unit change the filters and oil should stop that issue 👌💞

[@rhyslewis2062]

@@Mobileblaster atlas copco 180cfm mare.... I seen you might be selling yours buddy

[@Mobileblaster]

@@rhyslewis2062 no mine is not for sale 180 is about the best all rounder I would service and keep using that.

[@cengizpocan296]

Enemy of human health

[@Mobileblaster]

What's that?

[@cengizpocan296]

@@Mobileblaster sand blasting process is very dangerous for lung health. Because of lung ca

[@Mobileblaster]

Not in the products I use. I use a media that's none carcinogenic and the paint removed is water based paint. I wouldn't recommend breathing it in but it is clean dust 👍💞

[@AlamgirHossain-yw8in]

I know this job

[@Mobileblaster]

😊👌👍

[@RTH1207]

🙂👍🇳🇴

[@Mobileblaster]

🤘👌💞

[@valterunger4141]

good good but not homogeneous enough ,time was short )) fuck this job ,but i like made ))

[@Mobileblaster]

How would you switch things up bit?

[@valterunger4141]

@@Mobileblaster it's a job in which you have to develop yourself, and I'm still learning))) it's perfect when the iron is the same gray, for example, perfect clear ,good luck perseverance )))

[@Mobileblaster]

@@valterunger4141 I kinda want to get better at explaing what I'm doing, how I'm going to go about it and why but I totally get soaked into the job I forget about the camera :/

[@mrfajita1542]

Rust

[@Mobileblaster]

Best rust inhibitor man has invented 😏