Thanks so much for this video some fantastic simple little tips that make the job easy achievable!

Genius!!! Thousands of motorists have watched this video then asked themselves, 'why didn't I think of that...'

Should I put a little gasket maker on both sides?

I tried it and the light doesn’t blink. I have a 1994 Camry

WHY? you are not really giving any details of the fault and the WHY? It seems that these cars have quite a few ignition failures BUT its with the Switch not the barrel. Do you have any info about that fault as it seems to effect quite a few people and they would be finding this video which seems to be different and not really relevant?

You don’t show anything except your arms not helpfull

I'm a AAA battery technician and this battery is one of my least favorite to do.

Question for OP don't you need to bleed and get the air bubbles out? How do you do that?

Hello I tested spark plug if they don't touch each other inside I put on 20M ima and no reading which is good but my max resistance on volt meter is 200M OMS if input there and measure I do have reading. Which one is right?

👍👍👍👍👍👍👍👍👍👍👍

Thanks brother man

I subscribed thank you I jsut needed to make sure I did it right

I am not seeing any information about connecting the wire to make the turn signal work

thank you you make it look easy

Nice. Thank you

I almost did everything correctly. Then the filter cover was not coming off, so I thought I had to remove the screw that was above it. Then, I saw the video.

Good video! Clear and explanation and easy to understand!

That was useful, thanks!

just to avoid any possible headaches, if you have a B5, V6 manual. The passenger (right) side axle will *not* come out without disconnecting at least the upper control arms. No matter what position you turn the wheel in, or angles you use it will not come out. So unless you are comfortable with or confident they will come out cleanly, don’t attempt this. But the left side at least will go in and out no issue at all

The timing mark is on the valve cover

Where can I get that list at and I’m having trouble with my od light coming on won’t go off

Thank you 👍

To replace a simple dead headlight on a P T Cruiser is the most ridiculous labor ever! You're practically taking the whole front end apart JUST to put a damn bulb in.

Thanks 🙏

Car i use without thermostat pls reply thank u 💙

Why don’t you made a complete video including the thermostat bleeding

14-15 foot lbs? Wouldn't that strip or otherwise damage the bolt, thermostat housing?

Bahahaha What a scam.. lol. Who you kidding? On that note the really stupid people in this world will believe this . The poor saps

Thank you for clarifying this

I recently replaced a oil cooler gasket on a 3.0 V6. I used a hose clamp on the rear hose and removed it and was able to leave the forward hose on the cooler to swap on the new gasket. Just be careful how you position the cooler so the coolant doesn't come out on the side with the hosed removed.

Thanks - This was helpful. I had a mishap in a parking garage, and I needed to replace my passenger mirror with one from a recycling yard.

Thank you so much man. Its my first time doing any work on a car and this helped alot. Also using a long flat head screw driver helped me alot

Great Videos...I have my work cut out for me on my C4 Corvette. A small piece of sandpaper somehow got stuck to the microfiber towel I was using to buff out Mother's Spray and wax. I put scratches all over the car. A pro shop in town, "Classic Coach", advised me that the clear coat on a 1985 Corvette is very thin. I have the wool pad, Mother's #10 cutting and a good buffer, I'm just afraid of trying it. Hope the WD-40 works instead...

It works, I scratched my new Kia, by hitting Agaist side of garage which created black spot on side of the car. I used W40 after seeing the video and it took black spot off and made it as new.

60295 Amy Vista

1231 Hauck Row

Thanks alot bro

Video is to fast not enough info on installation part

OMfG what a friggin nightmare just to change a bulb or lense.

Thanks. 8 years later this video keeps on giving, for my 2015. God Bless

Thank you for the video I noticed you haven’t posted anything new since 8 years ago, hope everything is well.

Mine spins freely…..to a point should I be able to move it easliy from lock to lock, essentially?

such an idiotic design

Spinka Gardens

Great video. It is a relatively easy job

Cool project, LS swap! 😅

What happens if you lose the key.

this info helped me out and i'm truly grateful for it

Thanks matey, clearest on here

Kia Cee'd 2008. After I've done the replacement, everything electrical working, starter motor runs ok, but the engine turns, and turns but it does not start. Any suggestions?