Could you please tell me where to get the air sled lift cart?

Show

$1500 a day for that? No way without holding a gun on somebody.

You lost me with the whistling

Hi Handyman. Whats your setup for paint? equipment wise. Also did you sand after you sprayed the base?

What ecoflow delta is this the a few different kind

$1,500?! Really? C’Mon, Man - I’d like to see a breakdown of that… I enjoy your channel, and appreciate your humor (and even chuckled to myself about that daily rate)…

That's the bit.

Which eco flow did you use?

My mother's old bread knife😂

3xpensive with those cans

Wow you can tell you only do paint grade.

You actually got paid $1500 for that work today?😮

What do you charge an hour to make $1500? Or do you charge a flat rate for your jobs? Do you have a minimum charge or minimum 1,2 hours?

Could you do the round-over with a router bit and then sand smooth to save some time?

The video is informative. My question is why pre catalized primer is not used in the process.

I think it’s disingenuous to blame a sub-standard roller on the Rustoleum side that you purchased. The better sponge like roller could have been purchased. I also think the true test is after normal daily use what it looks like at year 1, 2 and 3.

Shark bites are not an alternative to copper. You don't want to bury shark bite fittings in the walls

How many amps is the disconnect box?

What I learned? The flashlight trick. I am certain I will use that in the future.

Thanks! Great video! What would you do if you did all this and then needed to trim off excess line set after it was installed? Would you turn off the refrigerant from the mini split, cut and reflare the lines, and then vacuum the lines again?

Brother, you just saved me a couple hundred dollars! ❤️

3:07 Wears watch, still asks Google for the Time 🤣💕👍 PS- you must be taking that door to the fair! 👏 did come out nice 👍

Nice job Handy 👏👍 1:11 How come you didn't miter those ends? Do you only miter the outside corners? 🤔

Great work and video! One question, the face frame inside dimension was 28-9/16 but what was the inside dimension of the plywood?

As of 2024, Lowes Appliance warranty is 2 days from date of purchase.

Thanks for this. I’ve been having problems with our ice maker freezing up & was contemplating the airflow situation.

Looks about the way I would do it. Not sure I would try picking up 94 pounds like that anymore, though. Maybe 25 years ago.

@ 13:00 that's exactly 25 square feet

Lol 🤣 handyman... Get a bandsaw!! All that mess cutting that cast piping.. for no reason. $100 at harbor freight. Would have taken 60 seconds at most to cut that. And would have been exponentially safer and much clearer of a cut. Come on brother. 🤦

My understanding is that you were a lectrician. Do you clean up your mess now that your just handyman, or do you still not sweep to maintain good professional standards?

谢谢！

I have a Toto tolet, it does not have a flapper. It's a totally different design.

It's not fun working under sinks and I can't lift the garbage disposal while turning that securing clamp. I need someone else to hold it up while I turn it.

Can you provide me a link to your other channel?

No wast my brother you putting out real content and many are learning so boom👊!!!❤️‍🔥👊

Question, do you put a clear coat such as Polycrylic over the top of the lacquer after the final coat? Is the lacquer durable enough to prevent it scratching off easily?

I replaced the blower motor of my AC unit after 10 years of service. Had to buy a puller to remove blower wheel. Cleaned 20 yo blower wheel. On startup there was excessive vibration. Got a new blower wheel from Amazon for $66 and installed it. No vibration and very much quieter than before. Lesson: If you remove an old part, replace it with new.

Obvious crap product for morons The concept is crap. Hate the ads. Go away forever.

"There is a potential for some errors", that's my catchphrase 🤣

Hi handyman! 🎉

Would you include the name ‘handyman’ in your business name? Seems like that is what people search for but also it might have a negative stigma attached to it

You are always the man with the video I need, and usually the last video I need for that job. Thank you!

Tell us why you got rid of your thickness planner

What router bit set are you using? I like how beefy those tools look. I tend to find a lot of the tooling they sell in consumer market places have specs that don't work for how I like to build my doors. Often when the specs are close to what I want, I find the tooling isn't beefy enough and have inconsistencies in accuracy.

This was a complete waste of my time.

Merry Christmas to you Handyman!

I've never seen anyone excited to pay more for doors... or really anything. But there's a first time for everything.

I got one of those mechanical pencil things. I figured if I spent a little more money I wouldn't lose it. The alternative was buying a thousand carpenter pencils and put them everywhere, but then I'd always be sharpening them.

I love your videos. You workshop stresses me out. Keep'em coming.