Chrysler 46RE Class Part 2 lesson 4

[@scatpack68]

Can't get any more clear and concise than this.

[@DavidFrost-t9y]

These videos are the best by far. Of any videos of watched on KZbin

[@utuber2940]

wow I wish I had a place to rebuild my transmission like this thanks for these videos truly appreciate them...

[@robinstaufenberg2706]

Thank you for such detailed instructions. I was hoping that you would go over performance rebuild techniques, and also the very important and complex set up of Overdrive piston clearance . I took a 47rh off a v-10 and have done the bore enlargement( at electric connector hole) for electric version, then used a 46re od unit, used 47rh od planetary and od apply plate, thus allowing a 47re build for use on my 96 cummins. OD worked great for about 5k miles, but now I keep cutting OD seals ( even with seal install tool). am currently repacking my (original) od to install on case, so detailed set up of od to main case clearance would be beneficial.

[@randy1ization]

you are a great teacher, thanks for making the vids, ive been interested in trans repair for a long time, and this video gives me confidence and sparks my interest even more. I have 2 chrysler a500 TO rebuild and will buy my parts from you.l

[@carloschambers1153]

Love your videos mr homes clear lessons

[@ericwakefield4977]

very good videos. made this such an easy project that I originally was frightened about. like others said you are a great teacher and dont leave anything out. thanks Jimmy!

[@D.JKennedy]

mine wont go down the rest of the way with the ring in it what did we do wrong 33:45

[@PaulRayburnAclearData]

Hi Your videos are awesome. They have been very helpful. I have a 2002 Durango with a 46RE transmission. We have replaced the rear band servo piston (which was cracked common problem) we were able to do in place ( without removing the tranny from the truck by sliding the overdrive assembly back and loosening and slightly lowering the valve body which allowed a long punch to get in an punch out the servo lever shaft. The problem were experiencing now on re-assembly is the rear band adjustment the adjuster screws in too deep before we can get enough torque on it. (it is just barely more than finger tight may 10 -15 inch pounds. The assembly feels like it is together properly nothing rattling and there is some tension. Any ideas?

[@bennyconas6556]

Is it true the older models like my 95 don't use a thrust washer for the reverse drum only a clip?

[@ronnieuncbug6221]

Thank you for the videos. Im about to attempt to rebuild mine. i have the ATSG book , but to actually see hands on really helps. Again thank you. But I have a question. When I ordered my rebuild kit the guy I talked to said that I should put a shift kit in it, I dont have the number he gave me. But I told him that mine is going into a 99 Durango and that Iam running 35 inch tires. Yes I have an external cool and also am running it through the radiator, so what do you think?

[@Avataranian]

25:24 18 N*m = 159 in*pounds, not 100. (I verified in the manual for it to be 17N*m, so who the hell knows).

[@Jacqui.VanHam]

So, there’s a thrust bearing in the end of the OD hub and it goes directly onto the thrust bearing on the piston? Face to face when you put the two cases together?

[@dciimho2798]

When did you install the intermediate shaft. In the video when you installed the OD unit to the main body of the transmission at 33:50 the shaft was not present but when you went to install the one-way bearing assembly it was present. I'm going to assume that there isn't anything particularly tricky about dropping in the shaft and installing the plastic washer and snap ring.

[@tombackhus7212]

I'm curious as well

[@PhilipHousel]

I noticed that too.

[@brokenwrist24]

I thought I had missed something, and went back and reviewed the video like 3 times. Sure enough, no intermediate in the od housing, but yet it magically shows up after torquing the bolts

[@Jerar-e9j]

@@brokenwrist24 I also saw it and was surprised, revised three times. this is a miracle!

[@Avataranian]

It slides right in, he had to remove it when it is flipped upside down (or it'd fall out). It's being used to line everything up,, there normally is a plastic version of this. When I got to this step it fell right in (assuming you did what he said previously and had it all lined up).

[@jeepsblackpowderandlights4305]

I have a 46re.. and its got 220k on it . Shifts fine still.. but it whines in 1st-3rd.. but once in overdrive and lockup and itz quiet.. downshift ti 3rd and its back. Why would the first 3 gears whine and get progressivly faster the faster you go. Doesnt do it in neutral

[@macdrew77]

You totally skipped the part on how to re-install the intermediate shaft?? How do I get mine to seat fully in the OD housing?

[@jimmywright5239]

My overdrive housing case does not sit flush against the bell housing case. Does the overdrive housing bolts pull it flush together ?

[@jimmywright5239]

Answer is yes.

[@jaxturner7288]

That end isn’t the bell housing end but anyway no don’t pull it together with the bolts. First it needs to be centered and the splines aligned and then tapped into place over the it’s snap ring. There is an alignment tool available to aid in the mating of the od unit to the rear flange.

[@killer2600]

I like how the intermediate shaft magically appears...It's fitting I guess, automatics work like magic and they go together like magic too. Is that why we call people like you transmission wizards?

[@zacharyirving5080]

if you do this with a manual handy (which you should) you'll see where it says to install an alignment tool to keep the OD section aligned. Thats all that is. Really would have been good to tell the folk at home that though i suppose.

[@ronnieuncbug6221]

wheres the last lesson? the one on rebuilding the front clutch?

[@justincampbell7938]

Where do I buy the servo kit

[@luisalbertoarteagatovar1984]

great video ser i like it very muc

[@rhkips]

Is there any advantage to using Trans-Gel over ATF when pre-lubing various bores during reassembly?

[@TheAbbytab]

+rhkips Yes. The gel will stay in place. Fluid will flow and thin out. Jimmy

[@rickd2391]

I have to point out the fact you never said the torque spec for the band adjustment it's 72 inch lbs then back off 3 turns

[@darrylhouska7965]

I’m rebuilding mine and I put the rear reverse band in and then try to put the rear drum inside the rear hand it doesn’t fit.. it’s the same band and drum that came out of it and there is not visible signs of damamge.. any ideas?

[@2cents422]

Mine didnt either. I put the drum in first then pushed the band over with a pry bar and pushed in the rectangular piece in with a pick. But then after all that I couldnt get the snap ring over the plastic thrust washer. It's gotta all come back apart for me to see why.

[@maam2164]

im having trouble getting the valve box in with the park lock rod

[@King_UnCaged_V1]

dose anyone know if this is the same for the 4wd trans

[@jamesg.1493]

how soon before the next lessons?

[@No-One1984]

Anyone else having problems installing a new reverse band that’s tight

[@donjackson8816]

I HEARD WHAT YOU SAID!!! DON

[@harryfischer6741]

25 ft/lbs? I thought everything was in inch/pounds?

[@killer2600]

300 in/lbs...there you go :D

[@fyre8442]

Just x12 or /12

[@راميمنصور-ب9م]

ممكن ترجمة للمهندس