How to replace Driver Side Suspension Knuckle Kit 2008-2012 Honda Accord

Buy Now!
New Suspension Knuckle Kit from 1AAuto.com 1aau.to/ia/1AAXX00305
This video shows you how to install a new suspension knuckle kit on your 2008-2012 Honda Accord. Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision.
This process should be similar on the following vehicles:
2008 Honda Accord
2009 Honda Accord
2010 Honda Accord
2011 Honda Accord
2012 Honda Accord
Tools you will need:
• Impact Screwdriver 1aau.to/oba/1AXAA00047
• Phillips Head Screwdriver 1aau.to/oaSS/1AXAA00013
• Pry Bar 1aau.to/oEM/1AXAA00020
• 10mm Socket 1aau.to/oaCN/1AXAA00017
• 12mm Socket 1aau.to/oaRj/1AXAA00015
• 14mm Socket 1aau.to/oaRj/1AXAA00015
• 17mm Socket 1aau.to/oaRj/1AXAA00015
• 19mm Socket 1aau.to/oVw/1AXAA00043
• Brake Caliper Hanger 1aau.to/ofm/1AXAA00084
• Pliers
• 1/4 Inch Ratchet 1aau.to/oaCN/1AXAA00017
• 3/8 Inch Drive Ratchet 1aau.to/oaRj/1AXAA00015
• Torque Wrench 1aau.to/oadI/1AXAA00044
• Gloves 1aau.to/oru/1AXSS00048
• Safety Glasses 1aau.to/omK/1AXAA00343
Subscribe: / @trq
Check out our playlist:
Honda Accord 2008-12 8th Gen: • Honda Accord 2008-12 8...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@bdream6501]

Thankful I found this. Why worry about pressing out a bearing when you can mess with a few bolts?

[@c0deman057]

Keep your original Lower Ball Joint Star Nut. The one that came on my suspension knuckle from 1A Auto stripped before it reached 60 ft lbs. of torque. I reused the old star nut just fine. I am very happy with this purchase and the video made it very easy. The grinding noise from my bad wheel bearing is gone. Thanks!

[@Abizzy84]

So it came with a new ball joint?

[@R3TR0R4V3]

Great video. These loaded knuckles are the way to go, especially for those without a press. Those damn bleeder screws always seem to snap, so I try not mess with them, unless I'm bleeding brakes. Just take the cap off the fluid reservoir and push the piston in, that way any air can escape and you don't have to worry about bleeder screws.

[@dnznznfjsnsnsms9996]

Do you need an alignment if you follow every ste you just showed here?

[@jiojimenez1120]

Does that trim ring works with the ABS system ?

[@helenlelidis1]

The bolt on my upper control arm ball joint spins with the nut when I try tighten it! Any tips??

[@ksakshm]

Hello TRQ, Was watching your posting 'How to replace Driver Side Suspension Knuckle Kit 2008-2012 Honda Accord' as i am ready to replace my 2007 Accord front driver side steering knuckle. In your video, when putting back the lower control arm, the castle nut and the carter pin were not aligned. in other words, the carter pin did not go in-between castle nut walls. Wondering if this is ok to not align? Please advise.

[@ziauddin7948]

good knuckle & hub replacement # 👍🇵🇰

[@pujo28]

Does the car need an alignment afterwards

[@ChmodX]

When will these be back in stock?

[@1chip4you]

I’m wondering where I can find the rear spindle knuckle to purchase

[@TRQ]

+@1chip4you Thanks for watching. Buy the part in this video on 1AAuto.com: 1aau.to/m/Shop-TRQ

[@wangbungal]

Where is the repair for the brake bleeder you broke.?😂