How to Wire Turn Signals AND Brake Lights into a ONE BULB |

"How to wire turn signals and brake lights into a single filament bulb?" is a question I often get. It is slightly tricky to do, but very doable with the help of some relays and a KZbin video. The key to making there whole thing work is understanding how a relay works, specifically pin 87A. That is the pin on the 5 pin Bosch style relay that allows this functionality to work. Hopefully this video helps you wire your tail lights and turn signals on your automotive project!
VIDEOS & PLAYLISTS:
➡ My Automotive Wiring Playlist: • Automotive Wiring How-...
➡ How to wire a relay with a positive or negative trigger: • 5 Pin Relay Wiring For...
➡ How to choose the right fuse and wire sizes: • What Size Fuse and Wir...
➡ How to wire an Inertia Switch: • Fuel Pump Inertia Swit...
➡ How to wire a Starter: • How To Wire a Starter ...
➡ How to wire a fuel pump: • How To Wire Electric F...
CHECK OUT MY AMAZON STORE:
🔗 Ratty Muscle Car Amazon store - amzn.to/3KKkCdP
🔗 5-Pack of 5-Pin Bosch Style Relays - amzn.to/3KSrYu6
🔗 Turn Signal Flasher - amzn.to/3UOTsFy
🔗 3 Position Latching On/Off/On Switch - amzn.to/3AdByCH
🔗 10 Pack of Fuse holders - amzn.to/3cU4CoD
🔗 272 piece fuse variety pack - amzn.to/3k48cNt
🔗 2 Pin LED Turn Signal Flasher - amzn.to/3yW8vBx
🔗 194 Light Bulb Sockets - amzn.to/3Hn7gSj
🔗 10-Pack of 194 Light Bulbs - amzn.to/3MXmaC2
🔗 Distribution Block / Terminal Strips - amzn.to/43M2XJD
*As an Amazon associate I earn from qualifying purchases.
*As an Amazon associate I earn from qualifying purchases.
SUBSCRIBE:
🔔 Subscribe to This KZbin Channel: www.rattymusclecar.com/Subscribe
🔔 My Project Car Rescue Channel / @projectcarrescue
🔔 Follow me on Instagram: @Ratty_Muscle_Car www.rattymusclecar.com/Instagram
🔔 Join me on Facebook: www.rattymusclecar.com/Facebook
CHECK OUT WIRING RESCUE MERCH:
WiringRescue.myspreadshop.com/
TAGS:
#RattyMuscleCar
#wiring
#wiringrescue
#automotivewiring
TIME STAMPS:
00:00 How to Wire Turn Signals AND Brake Lights into a Single Filament Bulb
00:30 Why is wiring a brake light and turn signal to one bulb hard?
01:08 The components in the circuit
03:40 The 5-Pin Bosch Style relay
04:14 The 4 Pin Bosch Style relay
05:32 Wiring the fuse box
05:50 Wiring Pin 87 on the relay
06:19 Wiring Pin 30 on the relay
07:03 Wiring Pin 85 on the relay
07:48 Wiring Pin 86 on the relay
09:10 Wiring Pin 87A on the relay
09:37 Understanding how 1 bulb can have 2 functions
10:35 DON'T FORGET TO SUBSCRIBE!
Please Note: This video description contains affiliate links, which means that if you click on one of the product links above, I will receive a small commission. This helps support this channel and allows me to continue to make videos like this. Thank you kindly for your support!
DISCLAIMER:
This video is for entertainment only. I am just a random guy on the internet, not an expert or professional. Do not try to reproduce anything in this video without the guidance of a professional as auto repair & electricity can be dangerous & destructive."

[@WiringRescue]

Thank You for Watching my Brake Light & Turn Signal Wiring video! Subscribe To This KZbin Channel: ​​kzbin.info​​​​ See My Wiring Playlist: kzbin.info/aero/PLsF7T1tRFy2hmiiUUfMZNyV-BUA_yrPIh

[@jeffreyharmon8345]

Love your system,but can't keep up,I have a new 18 circuit painless wiring harness, but still need relays right to run fan fuel pump air ride lights ect. Right ? Can I get a copy of this so I can do this? I have most of the things you show! Thank you for whatever you can help with!!

[@jeffreyharmon8345]

Can you help me please to understand better?

[@jeffreyharmon8345]

Thank you so much!!! Your very smart!!!

[@straightouttheshed]

can you expand this setup to include a hazard light switch? and what it would take to make hazards operate at the same time that brakes do? in other words single filament bulbs used in the rear for brake and blink but when hazard lights are activated the brake switch will still illuminate the rear lights solid, not blinking

[@AztecWarrior69]

​@@straightouttheshed Adding hazards is easy. Just use a DPDT (On-OFF) switch and a diode will do all of that. Can use that SPDT switch or a OEM on the column Turn Signal Switch. If you are making from scratch like on a dune buggy or ATV or Go Cart, then you can use just 2 relays, 2 DPDT Switches and 3 diodes.. Less wiring.

[@CheapAngler]

Dude, you're the Bob Ross of wiring.

[@WiringRescue]

That’s the best compliment I’ve ever received! Thank you!

[@marcr1333]

@@WiringRescueNow teach us CANBUS! New here so only teasing right now 😅😂

[@WiringRescue]

@@marcr1333- I’m slowly but surely getting there. Stay tuned. You’ll see one eventually! 🎉

[@sTeadFasT96]

Been trying to figure this out for a a while and you explained to me like I'm a puppy in elementary school, and it makes complete sense. Thank you!

[@WiringRescue]

I’m glad you liked the video! Thanks for watching. :)

[@ScottBailey.fingin.]

I've put off wiring the 1955 C750 for some time now, wanting to get this trailer wired to haul materials up north. I'm now ready to tackle both. Thanks for keeping it simple for me. Scott

[@Upaka16]

Its unbelievable how you explained this exactly how my brain receives info. Thanks for the knowledge my guy!

[@WiringRescue]

Thanks for watching. I do the videos this way because this is the way that I learn too! Glad you liked it, and if you get bored check out some of my other much more complex wiring videos, I bet you’ll like them!

[@Mitchellfab_customs]

Alright man, this is the fifth video I watched of yours. Now I'm inviting you to come to my house to fully wire up a rat rod from scratch. Because you make it look easy. Thanks for the videos

[@pulsar2121]

Ah! Of course, the power to the brake lights runs through the normally closed contacts. I was trying to wrap my head around this concept for days. With the help of your video, I was able to rewire my hot rod for combined turn and brake lights. Thank you very much for the detailed and simple explanation.

[@AztecWarrior69]

Would be considerably better if he provided a wiring diagram.

[@johnallen4900]

hi, i am an english guy [ 75 yrs ] - you certainly make the mystical art of auto electrics an awful lot easier to understand ! - i have just a couple of minor moans ! - 1. white wiring don't come out that well against the white pegboard , and 2. your blue wires suddenly become red ? otherwise , brilliant !

[@oregonsignalfan]

this video was really helpful!🎉 now I can finally seperate the stop and turn functions on my '11 ford ranger. Yellow rear turn signals for the win!

[@wowerman]

Yes, yes, yes!I did not know how is done in old school way.Nowadays you have computer to manage lights.

[@ryandick3768]

First off WONDERFUL videos I have learned from them. They way you explain and build them out os perfect. I've been combing through your videos looking for something matching what im trying to do on my 2008 Tundra. Right now, I have the ALL the interior removed and trying to think ahead on some wiring changes I want to do since I'm here. I don't want to remove all this again. I am making my truck kind of a "show" vehicle that is a "tactical" and have the ability to manipulate different aspects of "black out drive". Oneday will try and include a FLIR system (maybe). I am trying to do a -one switch activation to kill all rear lighting (i.e., breaks, reverse, marker) along with the interior door activation switchs (so if any door is opened, nothing indicates it). However, where I rub my head, do that this is not my level of expertise, is how do I have an indicator switch (when turned to "kill mode") indicate with no power to the rear lighting? Not the other way around, where the indicator is "on" when the lights are working, then is "off" when in "kill mode". I hope that makes sense. Any help would be greatly appreciated.

[@dang25272549]

Very Clear!

[@ernestoacompa5064]

Great video! I appreciate you!

[@WiringRescue]

Thank you! Right back at ya!

[@mimaspa1234]

great videos.. love them all

[@WiringRescue]

Thank you! I really appreciate it!

[@MW2mastr]

For hazard lights, switch needs a 4th position that sends power out both sides (to the 4 white wires) Therefore activates all 4 relays instead of just two. Or you could wire in a seperate hazard switch with its own power feed, send the power out to a flasher relay then the 4 white wires or pin 86 of all 4 relays

[@jamesford3549]

Another fantastic video. This series is an excellent resource for re wiring a car. Thanks for making.

[@WiringRescue]

Thank you! I’m glad that so many folks are enjoying it!

[@80zkids]

Great info! Can you incorporate reverse lights pls

[@amandeepkang4422]

Awesome!

[@AnthonyGarcia-lw4vg]

A beauty. Thx

[@ffemtdd]

Thank you so much!!! This worked perfectly although I had to do some major head scratching to get it to work. First of all my car is Positive Ground. Second of all the relay connectors I purchased were not wired as yours are. That took a bit to figure out. The clue was that the stop light switch activated the turn flasher..... oh, that's not right.....Once I realized the issue I just had to follow your chart and de-pin the connectors and re-pin as yours are. Oh, and I'm now subscribed!!!

[@WiringRescue]

That’s fantastic! I’m glad the video was able to help you out! Thanks so much for watching and subscribing!

[@shanek.odumodum9811]

Your videos are just awesome! You are blowing right through my mental blocks on electrical systems.

[@thebrian7channel474]

Nice video I’m working on a project truck what if I wanna hook up a trailer plug for the trailer lights to work do I wire them into the same circuit

[@thecreekfarm4761]

Enjoy your videos, very informative. I have a small tractor and headlights and fender marker lights turn on with a two wire switch. Ran new wires to fender lights and added a hazard switch, but would like all lights to come on with the switch but also for fender lights to work as hazard lights when I switch them on. I know very little about wiring, just enough to get me in trouble but also get some stuff done, but cannot figure out how get this done. Any Ideas? Possibly use a 5 pin relay? I have no idea what to do. Thanks

[@superiorpyro]

Great video series, thank you for your time and energy that you put into these! Quick question for you on the "ire Turn Signals AND Brake Lights into a ONE BULB" video: This is exactly what I need as I have completely removed all factory parts and wiring on a street/strip vehicle but in order to run the car on the street, obviously I need turn signals and brakes. That being said, I AM using std. 1157 dual filament bulbs up front and in the back of the car, so... Do I wire it the same way you demonstrate in the video or is there a tweak required because of the 3 contacts on the 1157's vs. the 2 contacts on the 194's in your demo? Thank you very much!

[@jerreplace6850]

This is explained really well. I’m trying to wire a jeep with single bulbs as running lights, turn signals, and hazard. Is this possible? I have it wired similar to this but instead of the brake light it’s the parking lights but it’s not working correctly. Any help is appreciated!

[@ReedCBowman]

Very useful, but I really wish you had included a wiring diagram. Or rather two: one of the whole circuit, and one just of the way the relays themselves work. Having both this general - but very clear - description, and the technical diagram you can refer to, would help full comprehension immensely.

[@WiringRescue]

All of this stuff comes straight out of my head, so I don’t have written diagrams for it. At some point I would like to make them, but there are only so many hours in a day. I do have a video on how relays work which you may find useful. kzbin.info/www/bejne/h3TOl3l5gcaSgMksi=6sYrYoNSMV3X__Mb. Good luck with your project!

[@ahmashnawaz1232]

Very nice explanation method, Kindly make video on how to add a circuit breaker between the main battery and wires in case of a short circuit….. thankyou

[@PredatorOmnivore]

thank you very much for this video. I do not like have the brake light turn off only to flash on the rear. I never understood having a one filament bulb having two functions. In the early 60s I rewired all my VW Bugs and Vans to have a separate rear double sided brake light with a separate amber left or right turn signal. Now I am wiring up a self powered 7 Way trailer light test box. I was really disappointed when I found out that the 7 wires in a 7 Way trailer light circuit used the terrible combined brake and turn signal system. I needed this circuit to duplicate what the towing vehicle "tells" the trailer. I just wish you had included much simpler to follow .

[@ElectroTree01]

Thank you for this video and the great explanation! I was able to wire turn signals, break lights, hazard lights because of this video. One suggestion I do have is to have a schematic somewhere in the videos so people don't have to (reverse?) engineer the video.

[@ElectroTree01]

@@AztecWarrior69 I added onto what was shown in the video using my electrical knowledge(just a dpst switch that switches both side turn signal relays at once)

[@ElectroTree01]

@@AztecWarrior69 I put them on a garden tractor. I did not require the ignition to be on in order for the lights to work(brake, hazard, etc). I definitely considered the fact that hazards disable brake lights with this arrangement but for my purposes, I don't think it is that important. If I was putting them on an on-road vehicle, I would have a separate brake and turn signal. I know that there are many alternative options which I could have just as easily tried(using arrangements of diodes, relays, switches, etc) but I wanted to try something a little different and I would probably use one of these arrangements in the future if needed.

[@ElectroTree01]

@@AztecWarrior69 Different was referring to something that I have not done before. I have used a combination of diodes and relays in the past. Maybe you didn't get the implication. Mowing, no. A project that is a video, yes. The extra draw is relatively small. Thank you for the offer but no thanks.

[@kano2444]

i need this for making ditch light DRLs flash with the turn signals. or I guess I could syphon off the power from the headlight ambers

[@straightouttheshed]

can you expand this setup to include a hazard light switch? and what it would take to make hazards operate at the same time that brakes do? in other words single filament bulbs used in the rear for brake and blink but when hazard lights are activated the brake switch will still illuminate the rear lights solid, not blinking

[@Droid6666]

Hello do you have a video like this that also show running lights and headlights. I would also like the head light to shut down when blinker is on. Let's with built-in turn signals. Thanks for any help. These videos are great. 😊

[@kasagupamaster]

Thanks a lot I learn on your video

[@RT0309ROOM]

Thank you for your good video, i have one question, how i can wire if i just have brake switch and turn signal switch, its for my jeep wrangler 2020, i change the rear light with led, but in my car i have 5 pin from car and on my new led light i have 4 pin, i try to put the brake light with turn signal, but When i push brake turn signal dont work, how i can wire ? Thank you

[@josedejesus617]

SALUDOS DESDE CALIFORNIA

[@WiringRescue]

Thanks for watching! Happy to have you here!

[@sanjeev3144]

Thankyou for this thoroughly well explained video!

[@WiringRescue]

You’re very welcome! Thanks for watching!

[@babybird57]

Great design and implementation, how's the 64 impala coming along?

[@WiringRescue]

Thank you! I actually decided to create a new KZbin channel recently for my rusty car projects, and I have a new Impala video over there. kzbin.info/www/bejne/aWqQlqSnedd6sLM Let me know what you think!

[@AztecWarrior69]

You can also add hazards by adding a DPDT Switch. Make use of those 2 red wires you are not using.

[@ciscokidfab7595]

Voodo magic!

[@jeffreyharmon8345]

Not good at wiring,but really want to learn!

[@WiringRescue]

Well you found a good starting point! I’ve got lots of wiring videos!

[@ronaldfears1847]

Great video, thank you! Quick question, would it be possible to use only 2 relays 1 for both front and back left and another for front and back right. Just trying to cut down on wiring because of small space. Thanks again, your videos have been very helpful!

[@Bubbibjoern]

Not if you want brake lights on the same 1 filament bulb...

[@joell439]

Fantastic and clear explanation 👍😎👍

[@WiringRescue]

Thank you much! I’m happy to hear you enjoyed it!

[@MH-rb7lp]

Awesome video. I am trying to figure out how to wire a set of taillights with essentially 1 filament bulbs. How would you integrate parking lights into this circuit?

[@nicholaskoenig3106]

Good question!

[@snoopyfix2]

Thanks for the video! It was a great help. However, I have an issue with wiring my brake lights. I seemingly have all my wires set up just like you, except I have 2 relays instead of 4. I have my left side together and my right side together. All the blinkers and things work great, but the brake lights, specifically, do not light up. They do not brighten when pushing the brake switch. It's a brake switch like the one in the video (it closes the circuit when pressed). When I have the brake switch wired to power and the switch wired to the relay, and I press the turn signal, the turn signal lights stay on when the brake is pressed, but the rear lights still don't light up??? They only brighten up when I disconnect the brake switch from a power source, and the blinker works as it should. Could this be because of my relays are bad? They are brand new and both do this.

[@rolandos64]

Can you show how to wire emergency lights w this same concept. Most scooters don’t come w emergency lights. I’d appreciate it a lot

[@WiringRescue]

I have a few other videos about wiring emergency lights. Here is one, though I think I’ve made at least 3 (check my wiring playlist). kzbin.info/www/bejne/q4nMdqKAi9l7n5o

[@captainover-tighten6729]

Truly amazing. Well done, again! Thanks. You got a subscriber for your efforts.

[@WiringRescue]

Thank you! It’s greatly appreciated!!

[@mzzzcruella]

Hi, I was wondering if you might know how to wire a side marker NOT to blink when the blinker is on, instead leaving it just on like the running lights? This is on a 07 trailblazer SS

[@brettbennett1740]

Can I hook the 2 red wires from the outside relays to the front parking lights and have parking lights and blinkers? 🤔

[@AngelGarage]

Thank you for your videos, it helps understand wireing in a way easy to understand. Im building probably world's first AWD V8 reverse trike motorcycle. You helped me understand the basics of electrical wiring in a car. Keep them coming.

[@urban_zebra]

You seem like someone who would know the answer to my question: i have a 7 way rv plug with turn signals yellow and green wires both hooked up along with a brake wire. When i hit my brakes, both lights light up np, however when i turn left or right, both lights flash. There is no other way to wire these wires unfortunately but can you think up a solution that will fix this issue for me ? I was told a recrifying diode would help but no idea on how to get that done. Thanks in advance.

[@robertpal4294]

So how would running lights brake lights and turn signals work together at nite?

[@dobbyrepairs]

Thanks for another informative video 👍

[@WiringRescue]

Absolutely! And thank YOU for watching them :)

[@AztecWarrior69]

You can also accomplish this with a single DPDT Switch and 2 relays. Less wiring.

[@AztecWarrior69]

Uploaded a video called "How to Wire Turn Signals AND Brake Lights into a ONE BULB DPDT Switch Two Relays".

[@patrickliverpool6487]

Congratulations to you. Amazing circuits clearly understand

[@WiringRescue]

Thank you! I’m glad you like them.

[@MAC0192]

Do you sell the complete kit for this? Working on a 1930 chevy stake truck with out signals.

[@WiringRescue]

I don’t, but I do have links in the description for most of the items in the video.

[@professionalguy5853]

I am trying to wire a canbus system that flashes ground on a motorcycle to the lights, but i am using a led light strip with amber turns. The hard thing about this is that the signal wire is shared for the brake and the turn. I need help trying to make the blinkers work without also flashing the brake light when both are engaged

[@Obsgabe]

How would I wire a turn signal to have turn signal and running lights together ? Trying to wire mirrors that have turn signals on a car that wasn’t equipped with them. I Ran it to a 5 pin relay and used turn signal as signal for relay but running into an issue where the turn signal on mirror and on headlight alternate back and forth. They don’t flash together. Is it possible ?

[@user-ve8uo8ue9s]

Hi, good circuit...but what I wanted is .. while the park light is on and when blinkers is switch on ...da park light must blink ..using 1 blub

[@IceCasasola]

will the hazard signal work the same?

[@metaldrivermd2333]

Great Video greetings from Argentina, this system is the same that DKW Cars used, the main difference Is there Is no relays, the car has a Ligth Switch that has on One side the Headligths Swicht and the other side the Turn Signals Switch, in the Turn Signals Side there's a output that goes to the brake Switch.Could you Made a Vídeo about installing hazzard ligths with this type of connection?

[@masedace3]

I agree, I would like to incorporate a hazard flasher into this system. I there a way to put a switch into the flash circuit from the factory flasher to function like the factory hazard switch?

[@tylerewald]

Can this be done without a signal switch? I have a brake wire and a turn wire that I’m trying to get working on the same bulb. Any tips help! Thanks!

[@Chevrolet1994]

Great video!

[@WiringRescue]

Thank you much! I was hoping people would enjoy it!

[@kennybiggs3944]

So awesome thanks for the information

[@WiringRescue]

You’re very welcome! Thank you for watching!

[@0008rrc]

Amazing videos👏🏽👏🏽👏🏽👏🏽👏🏽👏🏽

[@WiringRescue]

Thank you! I’m glad you enjoy them!

[@arkangelnorthman]

great job!!

[@JuanRamirez-pd2uc]

Do i have a taillight im working on Truck already has The following: Brake Signal Ground What would go in the flasher wire? Ive hooked all up and signal does not work whenever im pressing the brake, i had it working a couple months ago but stopped working all the sudden, any help would be nice. Thanks in advance

[@ethenlikestomakestuff9810]

So I have everything exactly like you however when I press the brake it is solid with a barely noticeable flash, how should I fix it?

[@parkerazz4385]

Is it necessary to have 4 relays for each bulb. Or is is possible to have 2 relays one for each side.

[@jimhiscott2918]

Check out "Kwik Wire" chassis wiring harness i was very surprised to learn when i bought there kit they dont use relays for any lighting for the exception of there flasher and emergency flasher. Other then that no relays? They do use fuses but claim relays are not necessary due to there AWG of wiring is so heavy. I would love for you to order there 8 curcuit kit as i did and do a review on it with an explanation for there thinking???

[@timpham8288]

Thank you for sharing your knowledge. I have a question about pin 87. I thought pin 87 always go to the load. Your video showed pin 30 connects to light bulbs. Is it matter or am I wrong? Thank again

[@WiringRescue]

Solid question, and you are totally right under normal conditions, which you can see in this video I made kzbin.info/www/bejne/h3TOl3l5gcaSgMk. However - this specific video is a special case when we are using them in reverse to get the desired result we need. As long as the proper fuse sizes and wires sizes are in place, it should function just fine. As I’ve said in a whole bunch of my videos, there are many ways to wire a circuit, and this is just one. :) Thanks for watching and posting this question - I wish I had planned better and answered this in the video itself! Ah well, each video I learn a little and try to make the next one incrementally better. Thanks again.

[@timpham8288]

Thank for answering my question. I spent 2 years in automotive program. I wish I had an instructor like you while I were in school. You make the most difficult subject to become fun and easy to understand. Best wishes

[@AirBerlin332]

I like your wiring, but one more question: while breaking and signaling a turn, how does the Relais stays on during flashing without a capacitor? In my mind, when the turn signal switches from on to off and back to on, in the off phase of the flash there isn’t power sent to the Relais, isn’t it?

[@joseovando5187]

Extra wireless.😮

[@cloterm]

5 relays, seriously??? Impressive materials savings! 😁

[@deassbt83]

I know others have asked but they either didn't receive a reply or their reply doesn't answer my specific question. Im employing this system but if i was to add hazards how would I do that? Could it just be setup for the hazards switch trigger pin 87 on all 4 relays and if so would anything bad happen if the turn signal switch got turned on? I understand with that setup the hazards wouldn't work without the ignition on, correct? I know this is a lot but would appreciate any advice. Thank you in advance.

[@Jerbrown]

solved me - thanks!

[@WiringRescue]

Excellent! Glad the video helped!

[@jaliennation9169]

is there a way to wire single filament without relays?

[@allenstyer2690]

Do you know how it works on an older car that has the power for the flasher going to the turn signal stalk/switch which distributes the power to the lights directly from the switch?

[@WiringRescue]

The old cars have a turn signal switch in the dash that is wired very much like the switch in this video kzbin.info/www/bejne/f6DCmmxmZpuiZ5I

[@brettbennett1740]

I need some help. I have a Ididit steering column and led headlight and parking light in one but I want the parking light to be turn signal and parking light. How can I get ahold of you.

[@MatthewSmith193]

This was a great video and really helped me solved getting the brake light and turn signal portion of rewiring my 1965 Corvair, thanks a bunch! One small request though, is there any way you could include how to have a brake switch connect to a relay to send power through pin 87A on the LR and RR relays? I was able to figure it out on my own but someone may need the heads up before they try to hook up their brake lights through a >5 amp switch.

[@AztecWarrior69]

"how to have a brake switch connect to a relay to send power through pin 87A on the LR and RR relays?" Did you not watch the video? That is the way it is in this video. Are you meaning to say that you want use the brake switch to energize a 5th relay and that is what connects brake power to the other two relays? And what's wrong with using a Greater Than (>) 5 Amp Switch?

[@arishoath8725]

Fantastic video!!! Quick question. I'm restoring a '36 Ford that originally used this circuit with single-filament bulbs, but I want to upgrade to a 3-wire (brake, tail, ground) LED unit so the lights are brighter. Does this circuit still apply, or could I run separate brake, turn, and tail circuits as if they were all separate bulbs, and then run them through one of those Curtis 4 to 3 wire adapters like you find on trailer towing kits? Thanks!

[@AztecWarrior69]

First off. "'36 Ford that originally used this circuit with single-filament bulbs" No it does not use this circuit. It does not use relays at all. It uses a slider turn signal switch. "and then run them through one of those Curtis 4 to 3 wire adapters like you find on trailer towing kits?" That's not how those kits work. You actually have to have the wiring already there. In order for you to have seperate the circuits at the switch by taking off the brakes and running it separate to the rear (whole new wire) "3-wire (brake, tail, ground) LED unit so the lights are brighter." It is not being 3 wire that makes it brighter, since the power draw is the same. It is the type of bulb, Gauge wire, quality of the switch, that are the determining factors of brightness.

[@chotuusian4127]

Good work

[@delhaley4380]

So how to convert a 2 wire brake/turn into a 3 wire without buying a converter?

[@kimwenceslaosanchez4449]

Is it applicable for Led Light bulb ?

[@RobertDickens2002]

You sir are a national treasure.

[@janrei9448]

this what i need on my motorcycle. thank you for this ❤️

[@janrei9448]

i just need 2 more 5 pins relay

[@BungAngus14]

What gauge wire would be acceptable for this application?

[@WiringRescue]

I’m glad that you asked, I made a whole video about that right here: kzbin.info/www/bejne/e5ndf2mLmdOghqM

[@BungAngus14]

@@WiringRescue Perfect. Also I posted a question for you in your DIY electric fan video. If you have a sec to answer my question it would be greatly appreciated

[@rafhan86]

Hi. What is the type of white board you used? Can share the board name?

[@VRMN8R]

Its pegboard

[@viewlover9271]

How about a wirring of hazard light

[@WiringRescue]

I have a variety of other videos about hazard lights - check out my wiring playlist!

[@zekesensei]

What kind of bulb do you use?

[@WiringRescue]

In general, all of the video descriptions have lists of the parts that I used in the video. In this case, the bulbs are single filament 194’s.

[@igorbarbarossa]

Freaking genius

[@WiringRescue]

Lol. Thanks for watching! I appreciate it!

[@cryptonaire-network]

Great video! I have any bike with pre-existing rear turn signals. Am I able to add front turn signals and wire them into the existing set up? As opposed to having two separate switches for front and rear turn signals? Thanks!

[@lenBrill1971]

You are a national treasure 👍🇨🇦🍻

[@WiringRescue]

Haha! Thank you! I’m doing my best!

[@moisesgovea6028]

Thanks for all your videos about relays, I have learned a lot from. I have a question about a 3 wire light for turn signal and side marker, I want it to cancel the marker when I put the blinker but don’t think it’s possible with one relay because if I wire the the marker to 87 and my blinker to 87a I would have to turn my side marker off via switch every time I would turn my blinker on for 87a to work. If I wire side marker to 87a I don’t think would work either. Any ideas would be appreciated ? Thanks again

[@AztecWarrior69]

The wiring is almost the same. Difference is that you will wire the running light circuit, to the side marks, in place of the brakes. And it can be done using only two relays. Of course you will need to Either change out your turn signal switch to a DPDT. Or use timer relays. It all depends if you are trying to do this as a "from scratch" wiring or trying to add this to non modified stock vehicle. So you should start by giving more details about the vehicle you intend to do this on. I have diagrams.

[@conbro23]

cool now add a hazard button haha

[@jamesford3549]

I’m not sure it’s legal to have a hazard button with single bulb stop/turn set up, as hazards on would mean no brake lights. Generally cars that used this set up were produced before hazards were invented.

[@WiringRescue]

Very true! I also have some other videos about hazard lights. Here is one of the simpler ones for reference kzbin.info/www/bejne/q4nMdqKAi9l7n5o

[@calvinmapp330]

What if only one side of my turn signals are working

[@chalokool1108]

I've been wanting to modernize the wiring on my 1966 VW bus for a while now using modern day relays and fuses and was wondering if any of your videos show how to wire a single LED tail light to work the tail lights, brake lights and turn signals since that'll be the almost the same on my VW bus which uses a single dual filament bulb to work all of those circuits. Great videos by the way.

[@AztecWarrior69]

Why? Unless you don't already have the wiring, then it is just a one for one swap. Fuse box: just upgrade and reconnect. Flasher: Swap out for an LED flasher. Lights: Swap out the lights for LED.

[@DavidS-dj7sn]

I would like to se this video with two 1157 bulbs

[@pmacc3557]

Don't suppose you can help me wire my old bike by email?

[@khancross]

Ok but this wiring is not usable for real because what is with parking lights?

[@danbarrett1167]

The issue is that when your at the back of a car and your trying to use this method, you dont have a switch to turn the relays on...No one is going to run a 3 way switch to the front of their car to be able to use their turn signals and brake lights...Just sayin...