INFINITI G35 🔧 Nissan 350z 🔧 BALL JOINT INSTALL

How to Diagnose a Bad Ball Joint? I show you how to replace your lower ball joint in your Infiniti G35 or Nissan 350z. All done with hand tools, no air tools or power tools needed.
The process applies to 03-09 Nissan 350Z, and 03-07 Infiniti G35.
I love KZbin and decided instead of consuming, I wanted to start creating! So please subscribe and I'll do my best to create the most entertaining and helpful videos possible for the G35.
Please subscribe to my channel.
2005 INFINITI G35 - 350 HP G35 - Dyno Tuned Gain +37whp/45wtq...... • INFINITI G35 / NISSAN ...
Performance Mods:
- KW v3 Coilovers
- Injen CAI
- NWP 75mm throttle body
- Motordyne MREV2
- Motordyne 5/16th spacer
- Motordyne v3 ART pipes
- Motordyne Shockwave TDX2 exhaust
#Infiniti
#InfinitiQ60
#InfinitiG35
#InfinitiG37
#Motordyne
#nissan350z
#nissan370z
#nissanGTR

[@tridentfd8482]

Maintenance before modding is key ! 🧐🔱

[@laughingexorcist7143]

Litterally sitting in my month old to me, 2006 g35 on jacks. Replaced camshaft position sensor, oil changed, rear diff. Fluid changed, front upper control arms, sway bar links upgraded, sway bar bushings upgrade, wheel bearings, doing lower ball joints and air filter replace now. Getting ready for carlisle PA as long as the governments COVID-19 doesnt keep it from happening.

[@ChuckNorris-cv5fc]

now is an engine swap or maintenance

[@speedracer2831]

​@laughingexorcist7143 you still have your G35? I'm in Bucks County. Bought an 06' Coupe RAS in 2018 w/ 13k original miles. Absolutely love the car!

[@speedracer2831]

Here i'am, again! I'm right around 70K original miles on my 06' RAS G35 Coupe. I love the fact i can come to this channel and see for myself what will start to fail, what i can do to pre-empt a major disaster, by staying in front of the failures to come.... So far i replaced the stock radiator with an all aluminum one. Rear Bearing Hub assembly, headlights, and the front bumper with an aftermarket Karuma Z (after i clipped a 🦌) I appreciate the time & dedication you have put into this channel.

[@ibanezrg320fm]

You have no idea how much i appreciate you man. For real, i usually click your videos as the first recommended video. You've helped me help my G more than anyone else.

[@speedracer2831]

💯

[@williamtahran2033]

Just wanted to say thank you for going over the details , I was not sure how to get the cone off the old ball joint . I see you used a three jaw puller , now I can finish replacing mine . I have a 2005 G 35 Sedan just turned 234,000 miles. Im replacing control arms , compression arms and ball joints . Thanks again man been a subscriber for about a year now keep up the good work !

[@MotordyneG35]

That's what I like to hear! 234k on a VQ is just breaking it in...LOL. You can also use a heat gun and then pry it off with a fork if you don't have the 3 jaw puller. Autozone rents the jaw puller too, so this job actually cost me $0. Ball joint replaced under warranty and I rented all the tools.

[@MotownCali209]

Seriously every time i plan on doing something, you upload the video i need

[@dirtyhandscleanmon3y]

you’ve helped me fix things on my G a few times. love that you love your car and work on it as much as possible yourself.

[@norontboyz5949]

Just picked up a 2006 g35x with 205k kms. My first Infiniti and i just stumbled across your vids. I am SO looking forward to owning the G. I've only had it for 3 days and i am officially in love!

[@kakashi99908]

Auto or dick shift?

[@dimpls33]

The most helpful video changing a ball joint. Torque specs were very helpful. One small thing, you should torque the inner control arm bolt under load. Just jack up by the ball joint until the load is just off the jack stand then torque it to 96 ft/lbs.

[@skyeroy29]

Miss the videos. Saw one where a guy was saying the rental kit he got wouldn't work and took his knuckles to a shop to get them pressed out and in. Glad I came back across your video to find out about that bigger kit. Got two greas(e)able ball joints from rock auto to install soon.

[@Turtlefarm]

If you have a dry underbody.. and you’re struggling with this… I feel your pain… keep at it… so satisfying after you finish and drive

[@alexisrojas1782]

Thank you !! Replaced my lower control arms and ball joints on 06 g35 coupe . Easy process i made sure to get the 23pc ball joint set from autozone , they gave me the small red box set but didn’t work . mpact gun would make it easier . I struggled to install the joints with wrench

[@foxxxxxi8814]

Really good video man , thanks!

[@jeflores1000]

Great video, thank you very helpful!!

[@cryptocomplete]

Great video. Very helpful details. I think I can do this myself now :)

[@vladzyzz9910]

Thanks bro , made the job easier

[@andys5203]

Awesome presentation 👏

[@Ashamp5207]

Update for everyone this large kit he is using is at Advanced auto parts Auto zone only has the small kit! Make sure you get the correct one like he explains! Thanks for the vid!

[@Ji9303]

You're lucky. I had to take my whole spindle arm off and used a 20ton press. No matter what it would not budge. Good job. Thanks for the videos

[@rafagas5150]

Ji9303 damn 🤔

[@SAULJman44]

Thank you for your videos, you the man! Been watching your videos for a while. Since I had my G and still watching now that I got a Z. I like to follow your videos because I can tell you really research how to do things to your car. Like looking at the factory torque spec for each bolt. Legit! Keep it up.

[@pefrovalenzuela9580]

Thanks for the info 👍 😀

[@autograph415]

thanks for the video, i dropped my g last week ( rim shot off whie driving mph) the onlt thing we can tell that needs replacing is the ball joint and praying thats it outside of my fender and possibly the rotar

[@Donnythelatemodeltech]

great information, keep it up!

[@nikogrinager7163]

Thx for the tutorial!! Mechanic wanted $1800 for ball joints and LCA’s. Watched the video thru a couple times and did the repair myself for only like $200 (this including the new LCA’s). Btw this was also my first ever repair on car.

[@MotordyneG35]

You are a true man that fixes shit, congrats!

[@terrybo5924]

wonder what it'd cost to do both my ball joints and tie rod ends at the shop. with help from this video and others, i did it myself. guy charged me $165 to do ball joints and sway bar links on my 98 camry.

[@juniorromero4126]

My G35 feels like it’s on clouds ☁️ This is a must do maintenance repair if u drive a bumpy G35 🙏

[@johnmichaelkarma]

well made vid, thumbs up #23

[@SeanPhelps-qh2eu]

Cool video, looks like the outter tie rod is next on your car.

[@gueroscla7801]

All I can say......tanks 👍

[@swagyrule3788]

i changed my lower control arm yesterday and when I drive my slip and vdc light turns on do I need to get it a alignment on my car?

[@BNew-xv4ce]

Great vid as always...I have a G35 06 coupe for about 4 months. I noticed now that I have squeaking or a rattling sound coming from my rear wheel area...I've been to several shops no one can tell me exactly what it is... any suggestions on what it could possibly could be? Sway bar links maybe?? Have u ever had this problem...ANY information would be greatly appreciated thanks in advance...keep the vids going👍

[@ahyungrocks5509]

Please help! Can't get the first bolt (or any bolts out). I've soaked it with some penetrating oil for over an oil, still would not budge. Just came back from Lowes with a impact driver (up to 150 ft-lb), but again without success. Wonder if I really need an impact wrench instead. Please advise.

[@ZR-kp4vo]

I just subscribed and I have to say you make some of the best videos for our cars . Thank you and what coilovers are you using?

[@MotordyneG35]

Thank you, I appreciate it. The coilovers are KW v3.

[@jalynejustin]

What’s up my man! I have a g35x 07. Has 134k miles I need a control arm passenger side. Do you think it’s better to change driver side also? Thanks

[@GioMauriello]

Just did my front left today, im gonna order new bolts because i couldnt get the damn sway bar end link off but i managed to squeeze the old one out still without removing anything but the tie rod and break line bracket💪🏼 ^ and ball joint bolts obviously

[@GioMauriello]

Perks of a 16 year old new england car

[@KGX470]

which bushings do you recommend to replace?

[@MrJimribs]

Great job easy to follow.....where did you get the service manual print out Thank you

[@luisfigueroa2011]

I have a 2003 fx35. The lower control arm is a bit different but it comes with the ball joint installed already and I was wondering if it is possible to replace the ball joint only like this video.

[@carlosbolanos5361]

When I hit 80 mph my G shakes the steering wheel . ( the steering is unstable pulls left and right ) I replace both tied rods ( inner ) , the wheel bearing's replaced, tires are new . Alignment done . ? Looking for knowledge

[@ClaudBol]

Have you replaced the lower control arm or the bushing on the lower control arm

[@g35tho11]

Where can I get all the service specs for my 06 g35 coupe? (I notice you got a sheet for everything you do)also does the washer on the bottom part of endlink go in the front or rear of LCA ??

[@kc_stetics8621]

Those KW Coilovers tho🤤🥵😩

[@randygentry1533]

Hey can you use this same kit for replacing the bushings ‽

[@babyh2121]

Great video! What’s your suspension setup?

[@HEEBEEJEEBEE9123]

I have a 2004 G35 Coupe and I need to replace my ball joints. Where did you purchase them? Would greatly appreciate your help. Thanks.

[@josevergaraazrealtor]

Where’d you get that light that goes where the exhaust is?

[@robb5289]

Where do u Jack up that area where the ball joint is just so i don't mess up any parts.

[@simondaughtry8079]

Hey man whered u get your nismo bumper from

[@xxlegend87xx2]

Just tried to do my pass side, no Carter pin, the bolt just keeps spinning and won't loosen front the ball joint, what do I do at this point? Been drowning it in wd40 and still can't crack the bolt loose from the post

[@lDolos]

Does the g35 have just 2 ball joints in the front? Or it has some in the back to

[@bigjohntheboss]

Where do you go to get your alignment done

[@chowchow2386]

I have an '05, 4 door, AWD version of the G35. Anyone know if same ball joint is used in both the rear and All Wheel Drive. The knuckle is different as is the struts. But did Nissan/Infiniti actually use 2 different ball joints?

[@randygentry1533]

Do you know how to install the white line bushing?

[@slow.lt1679]

Hey guys so I just installed this but my nut of the ball joint never gets tightened it’s that why you put the pressure under the ball joint

[@hero-tu6up]

hello, i am a high school student looking to buy my first car. i found this nice g35 (2006) manual with 122k miles going for $6k but i asked him if he would take $5k and he said yes. should i go through with the deal or not? i dont know manual so i will have to learn on this car too (if i go through with it)

[@austinbradley3411]

What size cup(sleve) was that?

[@Impossible251]

Hello, I saw on video you were going through mevotech Ball Joint please tell me name or any evidence this lower suspension. I have a problem, anywhere in manual there is no evidence on this, I would really appreciate it. Sorry with my eng, im from russian

[@vqgang3575]

Do u remember the size of the adapter u used ?

[@huntersteinbock3359]

anyone know where i can find individual door parts?

[@DragoMusivini]

Correct me if I am wrong but I believe those rotors were installed wrong. The slits should be point the opposite way in turn carrying the brake dust out and not in.

[@legollama88]

what part number is this kit? is it the power built kit?

[@Juice-jx1pr]

I to replace two of the compression arms they both were bad

[@mr.suavecito]

What’s the part number for the rental tool?

[@thegeneraljoe67]

Hi. Thanks for all the great Diy content , Tech info, & tips & tricks that you offer. I wanted to ask you a few questions concerning rims & tire sizes for my 2004 G35. The 20 inch set up i have is wearing out inside edge of both front tires. 275-30-20 on rears and 245-35-20 on fronts. The tires do not touch or rub anywhere. I have had 2 alignments done , along with getting a front end "shake down" looking for any worn parts and all seems ok according to shop techs. Is it possible this wheel set up is close to being too big for the car ? I'm wondering if i should change to 18 or 19 inch wheels / tire package , hoping it won't continue wearing the inner edges? Any thoughts?

[@MotordyneG35]

joe silvestri....rear camber kit. kzbin.info/www/bejne/rWbLgYOJo9aUf80

[@MotordyneG35]

joe silvestri ...front chamber kit. kzbin.info/www/bejne/jYSaf4mBrq-UnZI Even stock setup the inside of tires wear out too fast. Camber kits are how you fix it.

[@thegeneraljoe67]

@@MotordyneG35 THANKS VERY VERY MUCH !!

[@bre08005]

This video helped me a lot. I bought the harbor freight ball joint service kit as well as the master ball joint adapter set and was really struggling to find the right size. Once you mentioned using the one with the cutout at an angle I was able to solve my problem. It only took me 2 days ha

[@dfacedxa]

Nice work. Its awesome you can work on the car outside in February. Ive had to do it in NY and its fucked haha.

[@MotordyneG35]

Thank you! I spent 22 years in Ohio. Trust me, I know all about shitty weather. 89 days of sunshine per year from that hell hole. You think Arizona is death valley being on the east coast when in reality it is the next California.

[@dfacedxa]

@@MotordyneG35 Haha yeah Ohio has some shitty winters. Agreed on California, its becoming less and less attractive to move to. I go visit every couple years.

[@MotordyneG35]

@@dfacedxa ...I visit California often, it is not that is less attractive to move too. The barrier to entry in being able to afford housing is getting unaffordable to most. I think the recent statistic is 30,000 people a year are leaving California and moving to Arizona due to cost of living. When I first visited California from the east coast, it really is heaven on earth. Perfect weather year round, cliffs over coastlines.

[@dfacedxa]

@@MotordyneG35 personally, if i was going to move id want to be in a place that it is less restrictive to own a car, especially if i part of the move is to enjoy driving more. but i got mad love for california and agree with your points.

[@autograph415]

how long do u think it would take on average

[@Jamorant12grizz]

so the cup stays on the ball joint?

[@Ls1cutty]

How are the autozone ball joints holding up? Im debating whether I should get the autozone ones or Moog ones.

[@cryptocomplete]

@ls1cutty990 I bought one from Moog and even though the part number seemed correct, it just didn't fit. So bought one from Autozone and it fit perfectly.

[@LosVq]

Do you really need an alignment after doing this

[@DanielSanchez-rh5lp]

So after i replace the lower ball joints do i need to take it to get aligned ?

[@MotordyneG35]

Yes!

[@andrewaguirre7872]

What about all wheel drive

[@JowyCenatVlogs]

I support you fully & understand the need for marketing . But $21 for a Tee shirt ... dang

[@kakashi99908]

I know whats cheap huh

[@craigcarter4620]

How are the ball joints holding up? I’ve been told by many people that they are not serviceable you must replace the whole knuckle. This is why you can’t get a OEM ball joint from Infiniti.

[@MotordyneG35]

You are correct! There is no OEM ball joint from Infiniti, same with the rear diff bushing. They want to charge you 2k for a whole rear subframe assembly and I also replaced that bushing with whiteline for $100 in my rear diff subframe assembly. Not sure what Infiniti wants to charge for an entire knuckle assembly for this ball joint? No issues on the passenger side ball joint I replaced in 2013 or 6 years ago. The driver side was way past due on a new 1, it has never been changed. I'm sure the driver side ball joint I just installed, will net the same results as the passenger side.

[@joseplascencia4408]

U always wanna replace both sides at the same time for car alignment reasons

[@TomKaosOfficial]

Changed mine last year, they were a bitch lol. You made it look too easy 😆 good luck to the next victim haha

[@iselaherrejon1809]

My thoughts exactly!!

[@ElmeroJR11]

I have a problem with my 2004 g35 couple whenever I lock my car it doesn’t do the beep sound and I checked all my fuses and they all are okay can you help me please what should I do

[@xXTheGaMiNgBeAsTXx]

You still having that problem?

[@xXTheGaMiNgBeAsTXx]

g35driver.com/forums/g35-coupe-v35-2003-07/448684-lock-beep-sound-won-t-turn.html

[@ElmeroJR11]

Yes I actually fixed it with the website you gave me the lock and unlocked button at the same time it did unlocked the beep sound thank you so much !

[@kingdavid3457]

I allways brake thos end links dont know why

[@mustafagak2852]

I replaced my LCA's but not I cant screw the nuts ontop of the ball joints deep enough to be able to fit the cotter pin back through... Oops

[@cryptocomplete]

Did you ever figure out why?

[@abelgarza8716]

Where the hell do you do your repairs?! It’s always in the same spot looks like a parking garage at a hotel/casino

[@MotordyneG35]

I live in a high rise condo on the top floor, yes that is my parking garage. No it's not at a casino...lol.

[@dwayneblake9058]

Hey where is the transmission speed sensor located on the g35 coupe it’s code P1716

[@dwayneblake9058]

No that’s the code that came up saying turbine speed sensor I’m trying to see where it’s located on the 05 g35 coupe

[@dwayneblake9058]

Yes automatic transmission

[@hg9322]

What company is that black box kit

[@44special9]

Looks like it says Powerbuilt on it at the 3:15 time stamp

[@abijahasgedom4802]

Lmfao ur ball joint was non-existent Im dying

[@gabmastaqc]

cant see the merch?

[@MotordyneG35]

Thanks for the heads up. What country are you in? I don't think anyone outside of the USA will be able to buy merch. Here is the link.....teespring.com/stores/infiniti-g35-merch-2

[@jspansera]

Hey man sometimes when I go up a hill my G feels like it’s losing throttle response. It doesn’t throw any codes or anything. Any idea what it could possibly be?

[@TomKaosOfficial]

Whoisthis? 1st easy possibility.. maf sensor. Up hill only though?.. can be a lot of things, need to be specific lol

[@MotordyneG35]

Up a hill? Low on gas? Most likely you need to do this if no codes and cars is randomly dieing or lossing throttle...kzbin.info/www/bejne/nmeZZ4mEqLWpaK8

[@MannyVQ]

Which oil is the best for the vq35de

[@blacksheep6941]

Castrol Edge full synthetic 5w-30. Much better than Mobil 1 full syn. IMHO

[@MannyVQ]

black sheep what about motul ?

[@blacksheep6941]

@@MannyVQ I can't comment about because I've never used it. After switching to Castrol Edge from Mobil 1 my G runs smoother & consumes less oil. Check out Motordyne's other video about oil tests & comparisons.

[@blacksheep6941]

@@MannyVQ kzbin.info/www/bejne/l5TEfIaidpmiapI

[@MannyVQ]

black sheep I’ve been using motul , it doesn’t burn , I used mobil 1 once and it was garbage , Castro’s edge is good too

[@poptartgofast]

I'd rather them stall than pop the clutch burn out into the bay hitting the oil rack

[@zdarkassassins]

hey man what wheels are those?

[@MotordyneG35]

Over 10 years old and discontinued. Konig Crosshairs

[@zdarkassassins]

Motordyne G35 go any suggestions for my g37, im looking for a similair design

[@730F-Sport]

My front tires keep wearing sevearely on one side (inside) and not on the other (outside) even though I keep getting wheel alignments.. Is there any way to fix this pls help? (175,000 mi 2006g35 coupe)

[@MotordyneG35]

Please see my video on Front Camber kit install....kzbin.info/www/bejne/jYSaf4mBrq-UnZI

[@gruntythegreat3335]

Sounds to me like a classic case of bad struts

[@oneg35]

Can you provide link for that tool kit ????

[@MotordyneG35]

Like I said in the video. I rented it from Autozone.

[@oneg35]

@@MotordyneG35 obviously i understand that but i only see the red box at autozone or else i wouldn’t have asked for specific link to it .

[@MotordyneG35]

@@oneg35 ...you actually went to the store?

[@jedielectro]

hey man. I bet it gets hard to work on your beast . in a apartment building .with carrying all your tools about ! And not having a garage . are you the only one works on your car there ?. while others pay for some else do the work!. And , are you allowed to work on your car there ? but oh well, aye !. nice work mate. keep thos vids coming

[@MotordyneG35]

Thank you! It's actually a high rise condo, I live on the top floor overlooking the only lake in Phoenix, Arizona. I use the elevator and my tools are in a box on wheels so it is actually pretty easy. 70 degrees days in February. This is how I lay out at the pool to get a tan, my man, working on my car on the roof...lol. Smoking Flower while filming up so high is actually peaceful. Yes, I am allowed to work on my car in my parking garage. My neighbor has a Noble M400, Aston Vanquish, Aston DB7, Bentley Mulsanne and he also works on his cars out in the parking garage. He has put spark plugs in all of his cars and other maintenance. Putting spark plugs in the Aston was a pain. Here is a video of me working on the Noble M400 in the parking garage.......kzbin.info/www/bejne/enPOaYV7pZpph5I Eventually, I will get my own lift and the standard person garage.

[@jedielectro]

hey, that's cool. nice one

[@emanuelgarcia7446]

Bro you dont need to torque the nuts at the factory spec..thats stupid..