Stihl Fuel Line Repair

A look at how to replace a fuel line on an older stihl ms model chainsaw.
#smallenginerepair

[@michaelmceachern1084]

This is a great video. I have a 80s era 038 magnum and this helped. Hemostats! Brilliant 👌

[@TheGreasyShopRag]

Thanks for watching!

[@susanvaughn741]

Thanks for narration!

[@Devo491]

I use a tooth cleaning water-pic to clean up small parts. It's like a mini-pressure cleaner. Only about $50, and a great aid to dental hygiene.

[@TheGreasyShopRag]

That sounds like a good idea.

[@5153flash]

I just changed the same gas line and is was exactly like yours.I also cleaned carb. I put it all back together and the saw would not start. It was getting gas and spark,,but would not fire at all. Took me a minute to figure it out but I found you really have to tighten the carb nuts down to get a good seal. Did that and ran like brand new.

[@TheGreasyShopRag]

Good job figuring that out!

[@Devo491]

Yeah, I had to really lean on the wrench to undo the nuts

[@tedneitzel]

Just changed the fuel line on my 250 the other day and I've changed plenty for others and always got Stihl brand from dealer but they had a Oregon brand for me. I didn't notice any difference so it seems fine! Like you say the part that's in the tank always seems a bit short!

[@lorenz681]

You wouldn't happen to remember the model number that Oregon fuel line, would you?

[@tedneitzel]

@@lorenz681 I'm sorry I do not. It came from my Stihl dealer though!

[@chrischiampo7647]

Love That Bullshit Button 😊😀 I Agree Those Fuel Lines are A Pain to Change The Filter The Worst Is a TS-350 CutQuick Stihl 😩🥵🥵🥵😩 Great Job On The Diagnosis and Repair

[@TheGreasyShopRag]

Thanks!

[@BruceLyeg]

What was it you adjusted to stop it from bogging down at the end of the video?

[@TheGreasyShopRag]

The low speed carb jet. I struggled getting the screwdriver through the grommet and onto the adjustment screw, thats why I removed the cover.

[@beerman5587]

I'm back again I have 028 can you give me the number on a fuel line kit if there is a thing. I want to replace the fuel filter and the fuel line. Thanks for all the tips

[@TheGreasyShopRag]

I don't work at a Stihl dealer so you'll have to google the answer just like I would. Thanks or watching.

[@TheThirstycoyote]

Thanks 👍

[@TheGreasyShopRag]

Thanks for watching!

[@TheThirstycoyote]

@@TheGreasyShopRag got er done , my ms 270 would run like 20 minutes then bog out , same problem as you found , got a new line and slapped er in and Bob's my auntie , cheers 🍻

[@TheGreasyShopRag]

@@TheThirstycoyote Good job!

[@SluSharkND]

you gave us the "Later" then went back in for more surgery. How do you keep an a-hole in suspense? You'll tell me later........

[@TheGreasyShopRag]

Lol! Thats one of my favorite lines!

[@SonGoku-fj1uh]

I have ms180 she start fine but when i want to cut she stop in wood and wont cut.What can be problem

[@TheGreasyShopRag]

The chain stops or the engine doesn't have power?

[@SonGoku-fj1uh]

@@TheGreasyShopRag chain stop and when i pick up chain from wood go full gas work ok but when i go again to cut chain stop

[@TheGreasyShopRag]

@@SonGoku-fj1uh I can't be sure but it sounds like you are describing a clutch problem if the engine isn't bogging.

[@SonGoku-fj1uh]

@@TheGreasyShopRag i hope it is clutch not engine.thanks

[@SonGoku-fj1uh]

I look for clutch and it look ok tomorow i will change my carburator kit and my fuel line

[@davisemmy4345]

viy5x5 #von.ong