Haynow! What a find. The same carb. & same rebuild kit that I have. You took me threw it. 55 years old and it's my first carb. rebuild. The first job on my restoration of my 1968 Ford F-100 4x4 390. Thanks for the help.

Awesome! Not many people on KZbin have done or shown how to diy crown Vic coilovers. I’m thinking about doing what you do and was interested in knowing what coilovers you used. Btw what spring rate did you use?

Always enjoyed your content...ever considering a comeback?

GREAT VIDEOS I LIVE IN DALLAS AREA. I HAVE A 1961 F100, WOULD YOU DO THE CROWN VIC FRON END SWAP FOR ME? I DON'T MIND PAYING.

Very good video on vacum cannister adjustments and timming sequence.will use this today!

How’s the tmi seat holding up 4 years later?

Wondering how that comp cam has held up over the years; I've heard bad things about those.

Excellent video!

An after thought. Does that cam have advance built in? Some do.

Should have advanced it 4 degrees. You would have been glad you did. More low end torque and as the timing chain wears the timing will retard. Also better vacuum. If your looking for high rpm hp go straight up or retarded.

Thanks for the great video! I attempted to rebuild the carb on my 65 ford 3/4....now I can re-do it correctly!! thanks again for your kind assistance and expert knowledge to help this poor fiddle player out!

Lost me at LS (junk) 🤮 🤮

Fantastic informative video

We do this relieving in our shop, but not a lot of the crown Vic swaps. This has been one of the best videos I have found on the Internet for a little bit of instruction. Good job man.

Well done young man 👍 🔥 Great video 👍 Learned from it 👍👍

Nice truck. 390 sounds really good.

Awesome build, those u bolts for the bed… I can’t stand them, after a couple years they don’t wanna come off, the nut breaks free from the clip and just spins, anti seize the bolts and nuts. I live in Michigan as a collision tech, I’ve seen brand new trucks have issues trying to remove the bed.

🏁

What years of crown vic front crossmembers fit?

check the old one

What year crown Vic front end?

Sure seems like that it’d be a lot easier to do a total frame swap between the F150 & Crown Vic. Just saying.

It sounds incredible

Very nice welds by the way

Those hole on the bottom aren't the center of the front axle . The ob-long hole above them is center of the axle

Man... Haven't seen 3 in the tree in a Long Long Time. Done my heart good! Had a 73 F100;4x4 390 w/Granny 4speed

And why the same CV differential was not used?

What did you think of the 250lb spring in the rear or did you go with a different rate ?

I couldn't get mine out like this. I had to take the front clip off in my video. My engine is a 429 big block and wouldn't get over the front with my engine hoist.

Good job, no fear!

Any chance you are close to Medina OH? I saw the (330)

Nice setup.. I’m just started taking apart my 390 thinking about doing something Similar to yours mabe same cam setup..just wondering how did that build hold up..any tips or pointers would really help thanks

watching this 4 years later seeing those "5 dollar pinion shims" be 30 bucks now lmao

You mentioned the ride height was fully loaded…yet the bed was not on. Did I miss that part? Or do you consider the bed to have no significant weight?

Thank you sir🤟 super helpful. Put the video on and followed along and now my 66 camper special is ready to go. Great video🤙

Do the rods assembly lock to cap or opposite?

"so it'll stop faster than your dad's corvette"... then installs literal junk brakes on it... classic.

What brand spark plug wires did you use on the bump side Ford truck, those are blue also certain Ford and dodge vehicles are known for having electrical interference through the speakers when running lol

Use Vaseline to assemble... Silicone is impossible to get off and makes painting a nightmare.

Great video! I'm getting ready to rebuild a '56 F100. Do I need to create frame pockets?

How do you like the 390? We have a 72 f250 with a 360. We might built It into a 390. Give it more power would be good.

Great job. But why the music?

Kudos for posting this video... we've all been there.

What gears are in the rear end, and are they original to the truck? Also, what is ball park price you spent on parts and labor for that 390?

WHAT SIZE IS THE V BAND ON THE CAST LOG 2.5" ?

What gears are you running in the rear?

Awesome job on the motor

Time for a c6 and a high stall

Your instructions were clear and concise. Thanks for the help.

Hi there, what size wheels and tires are you running. I gone have the same set up.