Have same skid steer model, 1845C, yesterday was doing some work when noticed spray coming out of panel directly behind bucket in area where 'auxiliary' valve is for 'fast flow' hydraulics , first thought looked like water but soon realized was hydraulic fluid! Within less than a minute this leak emptied entire hydraulic reservoir? Well I was rather disappointed; now I have a dead machine. Took everything off I could and looked into front belly but could not directly see any broken hoses? Question: is there some way to trace down the leak, e.g., should I put some hydraulic fluid back in reservoir, start machine and see if I can see leak? Or, remove hose from reservoir and attach air compressor to it to see where it blows out? Or send you a plane ticket and let you trouble shoot it?

Good video ✅ I’m an auto electrician and was looking for fuses and this video came up , took it out and opened that control unit , it was melted .. couldn’t repair it , customer needed it same day for night work . They added light bars and more lights that burned the control box .. anyways. Great video saved me time to diagnose it back to the switch. Dont add more lights the relays are tiny inside this box . Cheers

I can see this works, but unfamiliar with the entire set up. I need a diagram.

97 f250 with 460 I had to remove starter. Other than that it went just like this video. I just tightened heater till it quit turning itself inside the hole.

You didn't use no tire lube. You can order a gallon from O'Rielly.

What year bed is this CM for? I have a 1996 F350 and CM says it only goes back to 1999.

How would you go about changing the chain from the center spline to the back left wheel on this exact model ? Could you do it from the access port as depicted in the video or would you have to remove the long top panel that runs the length of the machine and is below the foot panel (essentially giving access to the drive motors, etc.)

Thank you! I didn't have the right size spark plug socket. Now I feel dumb for not thinking of this😂

Its not rear window

Man, that is some FLAT ground!

Thanks for the excellent instructions, hmmmm, however, apparently I like having fingers, more than you do, because I DO NOT trust a jack to hold anything up. In your video you reached in to grab the bushing so, if the jack failed, for any reason, your fingers would have been squashed off. I use tools to put stuff in such spaces, or I use a lot of extra security spacer shims to hold up the weight.

I just installed a set on my ‘96 bronco but the front core mounts were thicker than the ones you showed. Do you think it’s fine if I remove the thick shims? Currently too tight to get them in there

With vibrating plate whackers, in my experience their main function is warming you up in the morning, as you try and start the thing in the furthest part of the trench from the reach of the crane, after it stopped unexpectedly, having happily wobbled all the way there !

Excelente video Amigo 👌

The vacuum doesn't work I tried it I used air to blow it out and had to use a camera and a noose to get the end of the plug out of the cylinder then turn the motor over 5 to 6 times then use air again then turned the motor over again then put a new spark plug in it then started the motor let it run for 5 minutes then changed the oil. It was on a 1996 ford f250 with the 7.5

Even if it is a Lemon you can make it work - and repair it 6400 keep their value

Can it leak coolant from the front end of the cooler?

you're a genius. I just got the problem. One spark plug was broken, so I'm trying to get it out. Question is how you did you get all the ceramic out and the core electrode out?

I’m wanting to know how you wired your 7pin ?

What is the part number for hydraulic rings on John deere 1250

took three guys haha

I have the straight 6 on the 04 Envoy and it was hard to get the spark plug out and I finally got it but broke the white part off and some of the pieces we left in the hole which I hope I got all them out. But after getting the new plug in I can't get the sparkplug socket out. Any ideas?

Ya didn’t show the bearing nor lock washer😮

Deere and ram trucks or you will go broke

Suspension air bags do NOT increase the load capacity of a PU truck! They can help with stability, raise the rear end, etc. however the load rating is depending on many factors such as axle, tires, frame strength.

Wanna send me that special tool setup? 😂 Good work man great explanation of what has to be done. I want to do the i beams and traction beams and these body mounts on my 97hd 2wd. I love energy suspension.

Great videos! I have my own TS 115a issues. It was losing power when working ground the other day and I thought they ran it low on fuel. I fought getting it started, but after bleeding at the injectors I got it started. It will idle for several minutes, but it will not throttle up. Any ideas? I'm leaning toward IP issues.

Just push the vehicle off. lol

God Bless these Mechanics!! This is some very tedious hard work!!!

thank you sir

Best video about this I've seen yet. The construction of these bushing assemblies is bizarre, and other videos aren't nearly this helpful illustrating how it's coming apart and going back together

PTSD

Hey man I got a stuck socket inside the throat hole of the spark plug bore filing it out by using different variety of files

Thanks!! Just got an 80's 1845. Needs lots of luv'n.

did you use the Threaded Rod on the Radiator Mount Bushing also? or is it 3/8? 7/16 for the cab mounts. going to do this tomorrow.

What is the recommendation on type of oil you use and then chain cases and how much each side I have the exact same machine that were just now starting to go through it

Great to see you again Blake. Hope all is well with you. Watching you from Sydney Australia.

I found tgey can mar the rim bad if you arent careful. Put some soap on the rim first and a little when pushing it off

Still sounded terrible 😊

Great video after how many miles need the new clutch?

Like it ,good job

I would do that.

Good Video

Great vid, keep 'em coming.

At 11:31 to 11:40 , I laughed my fool head off 🤣

I always enjoy your videos, thank you

Good to see you, Blake! Been quite a while. I am surprised you were working on those in the windy field and not at least close to shelter for a little wind break.

He's back! Great to see your doing well. Great video!

Even a blind squirrel can find a nut. Happy accident, miss your content

Good to see another video, Looks like Blakes in the equipment hire business after you've done your project. Kinda makes me wonder if somebody dumps equipment at lower hours or a hire shop/contractor went out of business and stuff went to auction.